GBC B1 Manual De Instrucciones De Operación página 9

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 31
3.
Skew Offsets (Only if Crease die is inserted)
The skew offsets can be adjusted to improve the angle of the crease
in the media.
i)
Print a 10 sheet job in
crease mode.
ii)
Measure L8 and L7 on
each sheet.
iii)
Calculate L8-L7 and divide
the average of (L8-L7) by
2. The number is "X".
Based on "X" and paper
iv)
size on the table below, search for input number "S" to change
either BG DP L REAR or BG DP XL REAR.
If L8>L7, skew offset BG DP L/ XL REAR is negative "S".
v)
If L8<L7, skew offset BG DP L/ XL REAR is positive "S".
vi)
vii) After inputting "S", print 1-sheet by crease mode.
viii) After measuring L8, calculate the difference between L8 and
original paper size mid position. Input this number into
"1Crease Mid", in the backgage menu to correct the crease
position.
BG DP L REAR
A4R
LTRR/LGL
210
216
X
0.025
1
1
0.05
1
1
0.075
2
2
0.1
3
3
0.125
3
3
0.15
4
4
0.175
5
4
0.2
5
5
0.225
6
6
0.25
7
6
0.275
7
7
0.3
8
8
0.325
8
8
0.35
9
9
0.375
10
10
0.4
10
10
0.425
11
11
0.45
12
11
0.475
12
12
0.5
13
13
0.525
14
13
0.55
14
14
0.575
15
15
0.6
16
15
0.625
16
16
0.65
17
17
0.675
18
17
0.7
18
18
0.725
19
18
0.75
20
19
0.775
20
20
0.8
20
0.825
0.85
0.875
0.9
0.925
0.95
0.975
1
1.025
1.05
1.075
1.1
1.125
1.15
1.175
1.2
1.225
Skew Offset Table
Multi Function Professional Puncher – B1
BG DP XL REAR
LDR
A3
12x18
SRA3
279
297
304.8
320
S
0
0
0
0
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
3
4
4
4
4
5
5
5
4
5
5
5
5
6
6
5
5
6
6
6
6
7
6
6
6
7
7
7
6
8
7
7
7
8
8
8
7
9
8
8
8
9
9
9
8
10
9
9
9
10
10
9
9
11
10
10
9
11
11
10
10
12
11
11
10
12
12
11
11
13
12
12
11
13
12
12
12
14
13
13
12
14
13
13
12
15
14
14
13
15
14
14
13
16
15
14
14
16
15
15
14
17
16
15
15
17
16
16
15
18
17
16
15
18
17
17
16
19
18
17
16
19
18
18
17
20
18
18
17
20
19
18
18
19
19
18
20
19
18
20
20
19
20
19
20
20
4.
Alignment Setting
Alignment is the distance of the Top punched hole from the side
edge of the sheet (viewed from the punch output orientation). This
distance can be adjusted by entering the Settings section (press Up
or Down arrow from the Home screen, and press OK for Settings).
Pressing Up arrow will increase the Alignment position, and
Pressing Down arrow will decrease the Alignment position.
ALIGNEMENT
13X19
330.2
0
1
1
2
2
2
5.
Clear Cover
3
3
The Backgage Depth setting and Alignment setting for Clear Cover
4
media can be adjusted using this function.
4
5
6.
Language
5
5
The LCD panel can be configured to display one of the following
6
languages: English; Francais; Espanol; Deutsch or Italiano.
6
7
7
Displaying Information on the LCD Panel
7
8
8
1.
Die type
9
9
The type of die set that is presently installed in the machine will be
10
displayed.
10
10
2.
Punch cycles
11
11
This is the total number of punched sheets the system has
12
12
processed.
12
13
3.
Firmware
13
14
This displays the current level of firmware of MFPP-B1.
14
15
15
15
16
16
17
17
17
18
18
19
19
20
20
20
"+" ON THE LCD
INCREASES
ALIGNMENT
OFFSET
"-" ON THE LCD
DECREASES
ALIGNMENT
OFFSET
EN
9
Tabla de contenido
loading

Este manual también es adecuado para:

7723867

Tabla de contenido