Die Set User Manual; Important - GBC B1 Manual De Instrucciones De Operación

8. DIE SET USER MANUAL

The die sets for the MFPP-B1 are intended to work with multiple paper
sizes and sheet feed directions. In order to accommodate different sheet
sizes this die set must be configured to the correct number of punching
pins and the die stop must be set to the proper position. The die label
contains information on the common paper punching sizes, for the
uncommon sizes
Table 8.1.
Glossary
LEF- Long Edge Feed- Indicates that the paper is being fed through the
machine so that the longer side of the sheet will be punched.
SEF- Short Edge Feed- Indicates that the paper is being fed through the
machine so that the shorter side of the sheet will be punched.
Statement Paper- 8.5" X 5.5"
Legal Paper- 8.5" X 14"
Ledger Paper- 11" X 17"
Pin Numbering
Die punching pins are numbered sequentially starting from the handle
end. Figure 8.1 shows a 47 hole coil die as an example. All square and
round hole die sets follow the same pin numbering format.
Pin #47
Figure 8.1 Coil Die Set Pin Numbering
Figure 8.2 Pressure Bar Removal
Pin Removal
Wire
Coil
2:1
Rnd
Rnd/Sq
US Paper Sizes
Canon Part Number 0259C011AA
259C007AA
0259C005AA
LTR LEF 2, 47 1, 23
LTR SEF 7, 42 NONE
STATEMENT LEF 7, 42 NONE
LEGAL SEF 7, 42 NONE
LEDGER SEF 2, 47 1, 23
9" x 12" LEF 1, 2, 47 1, 23
9" x 12" SEF 6, 7, 42, 43 3, 21
Wire
Coil
2:1
Rndl
Rnd/Sq
ISO Paper Sizes
Canon Part Number 0259C011AA
0259C015AA
0259C013AA
A4 LEF NONE NONE
A4 SEF 7, 41 4, 21
A5 LEF 7, 41 4, 21
A3 SEF NONE NONE
SRA4 LEF NONE NONE
SRA4 SEF 6, 7, 42, 41 4, 21
*For CombBind 20H Configuration Pull Pin Number 1
The above chart shows the information on which pins need to be removed to correctly punch each sheet size and configuration that the MFPP-B1 can
accept. For standard offering dies not found in the chart no pin adjustment is necessary.
Multi Function Professional Puncher – B1
please refer
Pin #1
Quarter Turn
Fastener
Wire 3/5/7
3 Hole
3:1 Hole
8mm
Rnd/Sq 8mm
Pin Numbers to Remove Based On Paper Size or Orientation
0259C012AA
0259C001AA 0259C002AA
0259C006AA
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
5, 31 N/A N/A
5, 31 N/A N/A
1, 34 NONE 3H/5H/7H
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
Wire 3/5/7
3 Hole
3:1 Hole
8mm
Rnd/Sq 8mm
Pin Numbers to Remove Based On Paper Size or Orientation
0259C012AA
0259C001AA 0259C002AA
0259C014AA
NONE N/A N/A
5, 30 N/A N/A
5, 30 N/A N/A
NONE N/A N/A
NONE N/A N/A
4, 5, 30, 31 N/A N/A
Table 8.1 Pin Removal Guide
To remove punch pins from the MFPP-B1 first turn the two Quarter Turn
Fasteners CCW direction to release the pressure bar. Remove the
pressure bar and set aside.
to
Note: Lubricating oil may be present on the die pins, wear gloves if
needed.
Lift up and remove the desired pins according to Table 8.1. Store pins in
the pin storage tray inside front door of machine making sure pins cannot
be dropped, damaged or lost while removed.
Replace the pressure bar by lining up dowel pin holes with exposed
dowel pins. Hold pressure bar so that it is seats completely over dowel
pins and then rotate Quarter Turn Fasteners clockwise until a click is felt
to lock pressure bar in position. The pressure bar can be locked only if
the orientation is correct, it cannot be locked in any other

Important!

Before reinserting, clean the punch pin to remove any dust or foreign
substances.
Make sure pressure bar is attached and both Quarter Turn Fasteners
are in the locked position prior to inserting the die set into the machine
or serious damage can occur to both the machine and die set.
2/4 2/4 2/4
Hole Hole Hole
8mm 6.5mm SCAN
0259C008AA 0259C009AA 0259C021AA
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
2/4 2/4 2/4
Hole Hole Hole
8mm 6.5mm SCAN
0259C008AA 0259C009AA 0259C021AA
2H/4H 2H/4H NONE
2H 2H NONE
2H 2H NONE
2H/4H 2H/4H NONE
2H/4H 2H/4H NONE
N/A N/A NONE
Figure 8.3 Pressure Bar
Figure 8.4 Pin Removal
Dowel Pin Holes
Figure 8.5 Replace Pressure Bar
VeloBind VeloBind
11 Hole 12 Hole CombBind
LTR A4
0259C003AA 0259C020AA 0259C004AA
NONE N/A 1, 21
N/A N/A NONE
N/A N/A NONE
N/A N/A NONE
NONE N/A 1, 21
NONE N/A 1, 21
N/A N/A 3, 19
VeloBind VeloBind
11 Hole 12 Hole CombBind
LTR A4
0259C003AA 0259C020AA 0259C010AA
N/A NONE NONE
N/A N/A 4, 19
N/A N/A 4,19
N/A NONE NONE
N/A NONE NONE
N/A N/A 4, 19
EN
orientation.
11