DWT Berserker SBH10-26 VB Manual Original página 21

grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations�
• Note that when you operate a power tool, please
hold the auxiliary handle correctly, which is helpful
when controlling the power tool� Therefore, proper
holding can reduce the risk of accidents or injuries�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
safety warnings
• Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss�
• Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury�
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock�
Notice the power voltage: in power connection, you
must confirm that if the power voltage is the same to
the voltage marked in the tool's data plate� If the power
voltage is higher than the appropriate voltage, the acci-
dents will be resulted to the operators, and at the same
time, the tool will be destroyed� Therefore, if the power
voltage has not been confirmed, then you shall never
plug in arbitrarily� On the contrary, when the power
voltage is lower than the required voltage, the motor
will be damaged�
Safety guidelines during
power tool operation
All instructions have to be read� In case of
using the machine not in accordance with
the following provisions, electric shock, fire
or serious injury may occur�
• Check that the drill bit has been clamped in proper
position or not prior to operation�
• Power tool working will generate vibration and you
should carefully confirm that screws in different places
still are tightened or not prior to operation�
• Wear blinder in operation to protect eyes�
• Maintain the keenness of the drill bit so as to achieve
the optimum and safest efficiency.
• When replace or assemble the accessories, the op-
eration must follow the instructions of the accessory
strictly�
• If the productor has any problems, you must not try
to repair personally, please take it to the local assigned
maintenance center for inspection�
• Fix the workpiece as far as possible� The workpiece
shall be fixed with fixing device or pincer pliers, which
shall be fastness than holding the piece in hand�
• Before powered on, the switch must be confirmed
in "off" position; before you put down the power tool, it
must be turned off and the power plug must be pulled
out�
Special
• When the accessory is totally static, then the power
tool can be put down�
• Never let the power wire touch the drill bit or sur-
rounding parts in operation, or the power wire may be
damaged� The power tool with broken wires must not
be used� If the power wire is damaged in the working,
then the damaged wire must not be touched, and the
plug must be pulled out immediately� The damaged
wire shall increase the danger of user's electric shock�
• Chiseling walls, floors or on similar occasions, pay
attention to keep away from gas, tap water pipeline
and electric wire and operating tools in those places
shall keep away from touching metal parts� The appro-
priate detector shall be used so as to find out the loca-
tion of the concealed power wire� Or you can require
the relevant data from the local power supply entity�
The wires that are drilled through shall result in the fire
and electric shock� The damaged gas pipe will resulted
in the explosion� If the water pipe is drilled through, the
property loss will be caused�
• If the accessory installed on the power tool gets
clamped, the power tool must be turned off immedi-
ately and stay calm� At the time, the power tool will
generate ultra-high reaction torque, and result in the
return stroke� The accessory installed on the power
tool is easy to be clamped, like: the power tool is in
hypercharge, or the accessory installed on the power
tool inclines in the workpiece�
• The concealed electric wire or the power wire of the
power tool may be cut off in operation, and then the in-
sulated handle must be held to operate the power tool�
If the power tool contacts the charged circuit, then the
metal parts on the power tool shall conduct electricity,
and the operator may have electric shock�
• Two handles of the productor must be held with
both hands tightly in operation, and the base must be
stable� Both hands can hold the power tool stably; one
hand operation must be avoided�
• The flat chisel must not be used in the rotational
state (such as rotary drill and hammer drill), or the chis-
el will be blocked and the power tool will lose control�
• Only when you wear gloves then you can touch the
accessories, the drill bits and accessories will be hot
in operation, and it is easy to get burn� Never imme-
diately touch the drill bit or parts around it upon the
end of work, for those parts will be scalding and scald
your skin� Wear gloves and middle rest can reduce the
vibration and the injury to the hands and arms�
• Hands and body must not be placed between the
power tool and the wall or column so as to prevent
the power tool from flying off when the drill bits gets
blocked�
• In case using extended power wire, please use dou-
ble insulation power wire with the same specification
as the power tool�
• Avoid stopping an electric tool motor when loaded�
• Never remove any chips or fragments with your
electric tool's motor running�
• Never change the borer and chisel design or use
attachments and appliances, which are not recom-
mended for your electric tool�
• When working, never press the electric tool too
hard, as this might lead to the borer or chisel seizing
and motor overloading�
• Avoid the drill, borer and chisel seizing in the materi-
al worked in� If this happens, do not try to release them
with your perforator's motor� It may damage the motor�
• Never force out the drills, borers or chisels stuck
in the material you are working on with a hammer or
other objects the chipped off metal particles may harm
both the operator and the persons who are nearby�
English
Autogoods "130"
20