Craftsman 580.752101 Manual Del Operador página 13

7. Engage trigger lock on spray gun and start engine
following instructions How to Start Your Pressure
Washer.
8A. If using cleaning tank, rotate detergent shut-off valve on
cleaning tank to "On" position (A).
IMPORTANT: If using detergent siphoning hose, make sure
detergent shut-off valve on cleaning tank is in the "Off"
position.
8B. If using detergent siphoning hose, place small filter end
of detergent siphoning tube into detergent container.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the filter into a detergent solution bottle, route
the tube so as to keep it from inadvertently contacting the hot
muffler.
NOTE: Make sure the filter is fully submerged in detergent
while applying detergent.
9. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
10. Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
IMPORTANT: When using the detergent siphoning hose, you
must flush the detergent siphoning system after each use by
placing the filter into a bucket of clean water, then run the
pressure washer in low pressure for 1-2 minutes.
Pressure Washer Rinsing
After detergent is applied, scour the surface and rinse it clean
as follows:
1. If using cleaning tank, rotate detergent shut-off valve on
cleaning tank to "Off" position.
2. Rotate PrecisionSpray™ Selector to a high pressure
position, as described in the PrecisionSpray™ Selector
instruction sheet.
All manuals and user guides at all-guides.com
3. Keep spray gun a safe distance from spray surface.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer from
• Firmly grasp spray gun with both hands when using high
A
4. Apply a high pressure spray to a small area and then
5. Start at top of area to be rinsed, working down with
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.
1. Engage trigger lock on spray gun.
2. Place detergent siphoning tube/filter in a bucket full of
3. Rotate PrecisionSpray™ Selector to a low pressure
4. Flush for 1-2 minutes.
5. Shut off engine following instructions How to Stop
6. ALWAYS point gun in a safe direction and squeeze spray
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
• Keep high pressure hose connected to pump and spray gun
• ALWAYS point spray gun in safe direction and squeeze spray
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
the warm water onto the ground.
13
WARNING
Kickback from spray gun can cause you to fall.
a ladder, scaffolding, or any other similar location.
pressure spray to avoid injury when spray gun kicks back.
check the surface for damage. If no damage, proceed to
step 5.
same overlapping strokes used for cleaning.
clean water.
position, as described in the PrecisionSpray™ Selector
instruction sheet.
Pressure Washer and turn off water supply.
gun trigger to release retained high water pressure.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
while system is pressurized.
gun trigger, to release high pressure, every time you stop
engine. Engage trigger lock when not in use.