Idiomas disponibles
Idiomas disponibles
ENG
USE INSTRUCTIONS.
Before starting up the sander, we recommend
►
that you carefully read all of the instructions as
indicated
Please respect all regulations regarding
►
the prevention of accidents, health and safety
directives, laws and applicable restrictions for work
places
The sander must only be used by persons
►
who have been instructed in its use and only for the
purposes for which it has been designed.
POWER SUPPLY.
Make sure the power supply is adapted to
►
the requirements shown on the information
panel of the sander (1)
voltage will make it operate slowly
reduce performance and may cause the motor to
overheat.
EXTENSION CORD.
If the working area is at some distance from the
►
power supply, use an extension cord of enough
diameter and quality.
OPERATION.
To turn the sander on, press the power switch
►
(2)
Move the sander in long sweeping strokes
►
along the surface being sanded, letting the sander
do the work (3)
Pushing down on the sander
►
slows the removal rate and produces an inferior
quality surface (4)
►
sander inclined, this can damage the base and
break the sandpaper (5)
work often
This sander is capable of removing
►
material rapidly, especially with coarse paper
produce the best finish possible, start with coarse
grit sandpaper and change gradually to finer and
finer paper
A final sanding with a piece of well-
►
worn fine sandpaper will produce a professional
looking finish that in many cases will need no
hand sanding at all
►
collection bag will fill up will vary with the type
of material being sanded and the coarseness of
the sandpaper
For best results, empty the bag
►
frequently and check the opening for clogging
When sanding painted surfaces, you may find
►
that the sandpaper loads up and clogs with paint
A heat gun will work much better to remove
►
paint before sanding
sander
Overloading will result in a considerable
►
reduction in speed and efficiency and the sander
will become hot
In this event, run sander at a no-
►
load condition for a minute or two.
Using the motor at low
►
This will
►
Never operate with the
Be sure to check your
►
The rate at which the dust
Avoid overloading the
►
DUST EXTRACTION.
The sander includes a integrated dust collector.
►
TO EMPTY DUST COLLECTOR.
While holding the sander and remove the dust
►
collector cup
collector to empty
collector
►
breathing hazard.
PRECAUTIONS TO TAKE WHEN SANDING
PAINT.
Sanding of lead based paint is not
►
recommended due to the difficulty of controlling
the contaminated dust
lead poisoning is to children and pregnant women.
CLEANING AND DISPOSAL.
All surfaces in the work area should be
►
vacuumed and thoroughly cleaned daily for the
duration of the sanding project
bags should be changed frequently.
FIXING THE SANDING DISCS IN PLACE.
Disconnect the sander from the power supply
►
before making any adjustments or replacing
accessories
with velcro (6)
so that their edges meet
place onto the base until it is firmly held in place.
SPEED SELECTOR.
The sander is equipped with a speed selector
►
To
The optimum speed adjustment for each
►
►
application mainly depends on the user's
preferences
preferable for hard materials and a lower value
for soft materials
removed increases with the spin speed.
MAINTENANCE.
The sander has been designed for a long
►
working life with minimum maintenance
Optimum use depends on correct care of
►
the sander and regular cleaning
accidents, always unplug the sander from the
power source before cleaning or performing
any maintenance
effectively using compressed air after each use
If compressed air is not available, use a brush to
►
remove dust from the sander
vents and switch levers must be dept clean and
4
English
Gently shake or tap the dust
►
Put again the cup in the dust
►
Sanding dust exhaust may create a
The greatest danger of
►
►
The sanding discs are held in place
►
Align the sanding disc over the plate
►
Press the sanding disc in
►
In general, a high value is
►
The speed at which material is
►
The sander may be cleaned
►
Motor ventilation
►
Vacuum filter
To prevent
►
