Idiomas disponibles
Idiomas disponibles
The user is allowed to program up to 32 tracks in CD mode, or 99 tracks in MP3 mode (in any desired order). Program mode is
activated while in STOP mode.
1. Press [PROG] on the remote to enter program mode.
2. Press [
] or [
] to select the track you want to preset.
3. Press [PROG] on the remote again to confirm the chosen track.
4. Repeat step 2-3 to programme more tracks. Once completed, press [PLAY/PAUSE] to start the playback of the
programmed tracks.
The unit has a BT streaming function. Pairing the unit with a BT device can be initiated by following below steps:
1. Press [STANDBY] on the remote control or main unit to turn on the power.
2. Press [MODE] on the remote control or main unit to turn on the BT mode.
3. In case the unit is not paired with any BT device already, "BT" will flash on the display.
4. Activate your BT device and select the search mode.
5. "Audizio Reims" will appear on your BT device list.
6. Select "Audizio" and enter "0000" as password (if necessary). A beep will be emitted to confirm a successful pairing.
7. To disconnect, press [MODE] to switch to another mode or cancel the BT function on your BT device.
There is a USB socket located at the front of the unit. When a USB device is inserted in the socket, press [MODE] repeatedly to
select USB mode. The unit will automatically display the total number of tracks. All playback features are the same as if you
were playing an MP3 CD.
The unit can only play .MP3 format files in USB operation. If the device is loaded with MP3's, but the display keeps showing
"NO", the format of your USB device might not be compatible with the unit. The unit supports up to 32GB of memory.
Plug a 3.5mm audio cable (not included) into your external player's line out and the other end into the audio in jack on main
unit.
1. Press [STANDBY] on the remote control or main unit to turn on the power.
2. Press [MODE] on the remote control or main unit repeatedly to select "Audio In" mode.
3. Play tracks on the connected device. If volume level of the connected device is too high, sound distortion may occur.
Should this happen, lower the volume of the connected device. If volume level is too low, increase the volume of the
connected device.
Inserting the plug of your headphones into the main unit's 3.5mm headphones jack will enable you to listen to the CD, radio
or other music sources in private. When using headphones, the speakers will be automatically disconnected. Use the
[VOLUME+] and [VOLUME-] buttons to adjust to the desired volume output level.
Setting the alarm clock
This function allows the system to turn on automatically and wake you using a beeping alarm, buzzer, CD input, USB input or
FM.
1. In standby mode, hold [AL.SET] on the main unit for three seconds. Alarm time 00:00 will appear on the display. Hour
digits of the alarm clock are flashing.
2. Press [
] or [
] to set the hour and then press [AL.SET] again to confirm. Minute digits are now flashing.
3. Press [
] or [
] to set the minutes and press [AL.SET] again to confirm. Alarm wake up source will appear on the display.
4. Press [
] or [
] to select wake to CD, USB, Buzzer or FM radio. Press [AL.SET] to confirm, alarm volume level will be
flashing. Note: alarm volume level setting is not available in beeping alarm setting.
5. Press [
] or [
] to preset the wake up alarm volume level. Press [AL.SET] to finish alarm setup.
Note: If "Wake to CD or USB" is selected but no CD or USB drive is inserted, the alarm will default to the beeping alarm
automatically when the alarm wake time is reached.
For 'Wake to Radio", the system will default to the last radio station listened to before switching off.
Activate/de-activate alarm function
To activate the alarm, press [AL.SET] once, the bell icon will be shown on the display. To cancel the alarm, press [AL.SET]
again until the bell icon has disappeared.
This function allows you to program the system to switch itself off after a set period of time. You can set your sleep time in
power on mode.
1. To activate the sleep function, press [SLEEP] on the main unit. The display will show "Sleep Timer OFF, 120, 90, 60, 45, 30,
20, 10" in steps at every press. The sleep timer value will be flashing on the display.
2. When the display shows your desired sleep time, release the button. The sleep timer is now activated. The display will
show "10" indicating "10 minutes" sleep time and so on. When the sleep time counts to zero, the unit will go off.
3. To cancel sleep mode, press [SLEEP] once again. The sleep function will turn off.
7
