HiLook PTZ-T5225I-A Guia De Inicio Rapido página 11

II. In-ceiling Mount
1. Drill the holes in the ceiling.
2. Remove A, B, C, D, and K from the dome, and set the
DIP switch.
3. Install the toggle bolts.
(1) Remove the toggles from the bolts.
(2) Insert the bolts into the screw holes on the dome.
(3) Rotate the bolts through the screw holes.
(4) Reinstall the toggles.
4. Align the toggle bolts with the screw holes on F, and
push the dome to the mounting hole on F.
Rotate the bolts again. The toggles will automatically
rotate down to secure the dome to F.
5. Secure the C to the A with three screws, and route the
cables through F for the speed dome.
III.Ceiling Mount
1. The cables of dome can be routed either from the top
or the side of the back box. For the cables routed from
the top of the back box, it is required to drill a cable
hole in the ceiling.
2. Attach the drill template to the ceiling, and drill screw
holes and a cable hole (optional) according to the drill
template.
3. Remove B, C, D, and K from the dome to set the DIP
switch, and restore them after the setting.
4. Secure the ceiling mount to F with screws (supplied).
5. Align the hook of the ceiling mount with unlock label
on the speed dome, and push the speed dome to the
ceiling mount and rotate clockwise to secure it.
2. 5-inch Speed Dome
I. DIP Switch
Table 1-8 Switch Functions
Switch No. Function
1 to 5 Set the address for the speed dome
6 to 7 Set the baud rate for the speed dome
8 Set the protocol for the speed dome
Set the video output mode for the
1 to 2 (Right)
speed dome
Table 1-9 Set Dome Address
Switch
Dome Address
OFF
0
ON
1
OFF
2
ON
3
OFF
4
...
...
ON
31
Table 1-10 Set Baudrate
Switch
Baudrate
2400
4800
9600
19200
Table 1-11 Set Protocol
Protocol
Self-adaptive
MAN_AD
The individual DIP switches, No. 1 and No.2 are for
setting the video output mode of the speed dome.
Table 1-12 Set Video Output
Switch
Video Output
TVI
AHD
CVI
CVBS
II. In-ceiling Mount
1. Remove C from A, and remove K, D, and B to set DIP
switch, and restore them after the setting.
2. Drill a hole on F according to the drill template
(supplied), and connect the cables.
3. Loosen E on both sides of A and make the locks in
internal position.
HD-TVI Speed Dome·Quick Start Guide
1 2 3 4 5
OFF OFF OFF OFF
OFF OFF OFF OFF
ON OFF OFF OFF
ON OFF OFF OFF
OFF ON OFF OFF
... ... ... ...
ON ON ON ON
6 7
OFF OFF
ON OFF
OFF ON
ON ON
Switch
8
OFF
ON
1 2
OFF OFF
ON OFF
OFF ON
ON ON
4. Push A into the mounting hole in the ceiling, and
tighten E with the screwdriver and the locks will
automatically rotate outwards to secure the in-ceiling
mount to F.
5. Install the trim ring.
(1) Attach the trim ring to the lower dome and align H
of the trim ring with G on the in-ceiling mount.
(2) After having firmly placed the trim ring to F, rotate
the trim ring in the direction of arrow to secure the
trim ring in place.
III. Ceiling Mount
1. Remove the 4 screws on A by a Phillips screwdriver.
2. Remove the in-ceiling mounting bracket.
3. Screw 4 bolts onto A by a Phillips screwdriver.
4. Route the cables from the top or the side of A.
Remove C from the A, and remove the K, D, and B
from the dome to set the DIP switch.
Restore them after the setting.
5. Mark four screw holes on F. If you route cables from
the top of the device, mark the cable hole on F and
drill a hole.
Secure the mounting base to the ceiling with set
screws.
(1) If the speed dome is installed to the wooden wall,
use the self-tapping screws to secure the mounting
base.
(2) If the dome is installed to the cement wall, drill
three Φ5 mounting holes onto the wall according to
the hole locations, and then insert the cement screws
into the holes and finally use self-tapping screws to
secure the mounting base to the wall.
6. Route the cables for the speed dome. Align the bottom
of the speed dome with the mounting base.
Line up the direction of arrow with L of the mounting
base.
7. Push the speed dome upwards and then forwards in
the direction of arrow. When the speed dome is
placed in position, the spring will automatically snap
into M firmly.
3. DIP Switch of Mini IR & 5-inch IR & 6-inch IR Speed Dome
Table 1-13 Switch Functions
Switch No. Function
1 to 5 Set the address for the speed dome
6 Set the baud rate for the speed dome
7 Set the protocol for the speed dome
Set the video output mode for the
8 to 9
speed dome
Set the terminal resistor for the speed
10
dome
Table 1-14 Set Dome Address
Switch
Dome Address
0
1
2
3
4
...
31
Table 1-15 Set Baud rate
Baudrate
2400
9600
Table 1-16 Set Protocol
Protocol
Self-adaptive
MAN_AD
Table 1-17 Set Video Output
Video Output
TVI
AHD
CVI
10
1 2 3 4
OFF OFF OFF OFF OFF
ON OFF OFF OFF OFF
OFF ON OFF OFF OFF
ON ON OFF OFF OFF
OFF OFF ON OFF OFF
... ... ... ...
ON ON ON ON ON
Switch
6
OFF
ON
Switch
7
OFF
ON
Switch
8 9
OFF OFF
ON OFF
OFF ON
5
...