Tabla de contenido
Idiomas disponibles
Idiomas disponibles
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Using the slide function
For extra wide workpieces, the machine is equipped
with a sliding function. When using the slide functi-
on, make sure to loosen the locking bolt for slide rails
(29). Pull the handle (2) away from the fence (9) until
the saw blade is in front of the workpiece. Slowly
guide the tool arm downwards using the handle and
afterwards push the handle (2) towards the fence (9)
and saw through the workpiece with uniform feed.
For small workpieces, it is possible to fix the sliding
function in the rear position of the saw with the
locking bolt for slide rails (29). If more cutting width
is desired, then it is necessary to loosen the locking
bolt for slide rails (29).
Using the length stop (Fig. O)
The length stop (8) on both the left and right table
extensions (10) can be used for easily sawing
workpieces to the same length.
1. Move the length stop (8) upwards;
2. Loosen the locking bolt for table extension (34);
3. Adjust the table extension (10) to the required
length.
4. Tighten the locking bolt for table extension (34).
Adjusting the depth stop (Fig. P)
The depth stop can be adjusted, to limit the cutting
depth. This can be used to easily saw a groove. To
do so:
1. Loosen the knurled nut for depth adjustment (45);
2. Adjust the knob for depth adjustment (24) to
the desired depth;
3. Tighten the knurled nut for depth adjustment (45).
Switching the laser on/off (Fig. B)
Press the laser switch (46) to switch the laser on
or off. The laser switch (46) also turns on the LED
worklight.
Changing the speed (Fig. B)
The mitre saw is equipped with two speed modes,
that can be changed using the speed selection
switch (52). Generally speaking, use the lower speed
'I' for metal. Use the increased speed 'II' for wood.
• To operate the mitre saw at a speed of 3200/
min (metal), put the speed selection switch (52)
on the 'I' position.
WWW.VONROC.COM
• To operate the saw at a speed of 5000 rpm
(wood), put the speed selection switch (52) on
the 'II' position.
Fine-tuning
Prior to any adjustment work disconnect
the mains power plug.
To ensure precise cuts, the basic settings of the
saw must be checked and adjusted before first use,
as well as necessary after intensive use. Suitable
special tools are required for this. Vonroc after-sa-
les will help handling this work quickly and reliably.
Fine-tuning the laser (Fig. Q)
Note: To test the laser function, the power tool
must be connected to the power supply.
While adjusting the laser (e.g. when moving
the tool arm), never activate the on/off
switch. Accidental starting of the power
tool can lead to injuries.
If the laser (18) ceases to indicate the correct cut-
ting line, you can readjust the laser. To do so:
1. Open the cover screws (47) to remove the front
cover;
2. Loosen the laser adjustment screws (48) and
set the laser by moving it until the laser beam
strikes the teeth of the saw blade (6);
3. Mount the front cover by tightening both cover
screws (47).
Fine-tuning the 0° bevel angle (Fig. R, S)
1. Adjust the mitre and bevel angle to 0°;
2. Lower the handle (2) and secure it using the
position lock knob (38);
3. Lock the slide movement using the locking bolt
for slide rails (29);
4. Set an angle gauge to 90° and place it on the
table (11), as shown on figure S. The leg of the
angle gauge must be flush with the saw blade
(6) along its entire length;
5. Loosen the lock nut for 0° bevel angle (50);
6. Adjust the stop bolt for 0° bevel angle (32) until
the leg of the angle gauge is flush with the saw
blade along its entire length;
7. Re-tighten the lock nut for 0° bevel angle (50).
EN
17
Tabla de contenido
