Safety Instructions; Description And Function; Intended Use; Connection And Operation - Goobay 60471 Instrucciones De Uso

EN
Wireless Quick-Charging Pad 15 W

1 Safety instructions

The user manual is part of the product and contains
important information for correct use.
• Read the user manual completely and careful-
ly before use.
The user manual must be available for uncertainties
and passing the product.
• Keep this user manual.
• Do not open the housing.
• Do not modify product and accessories.
• Do not short-circuit connectors and circuits.
A defective device may not be put into operation,
but must be protected against further use.
• Use product, product parts and accessories only
in perfect condition.
• Avoid stresses such as heat and cold, moisture
and direct sunlight, microwaves, vibrations and
mechanical pressure.
• In case of questions, defects, mechanical da-
mage, trouble and other problems, non-recover-
able by the documentation, contact your dealer
or producer.
Not meant for children. The product is not a toy!
• Secure packaging, small parts and insulation
against accidental use.
Dangers in the vehicle
Attention while driving may be impaired and seri-
ous accidents, personal injury and property dama-
ge may occur.
• Place the product so that the driver is not obst-
ructed.
• Do not operate your charging equipment whi-
le driving.
There is a risk that the charging device may fall or
become a skidding hazard.
• Do not pick up your charging devices while dri-
ving if they fall off the charging mat.
• Do not charge devices that are larger or thicker
than the surface of the charging mat.
• Only use the charging mat when the engine is
running.
Otherwise, there is a risk that the capacity of the ve-
hicle battery will be reduced to such an extent that it
will no longer be possible to start the engine.
Heat storage
Heat is generated during inductive charging.
• Make sure that there are no metal parts on the
back of your device (e.g. metal cover, metal plate
for magnetic holder).
Metal heats up strongly in the induction field and
can cause damage to the product or your end de-
vice.
• Do not cover the product.
Magnetism
The product contains magnetic materials.
• Consult a doctor before use to ensure compatibi-
lity with implanted medical devices.
• Keep a minimum distance of 20 cm from medi-
cal devices.
• Do not store and/or operate the product near
bank cards.
Tripping hazard
• Install the product so that no persons or proper-
REV2022-04-04 Subject to change without notice.
V1.0aw
ty can be injured or damaged, e.g. by falling, trip-
ping or the like.

2 Description and function

2.1 Product
The product is an inductive charging mat including
charging cable for wireless charging of smartphones
and other devices supporting the Qi standard with
up to 15 W of power. It is suitable for use in vehicles
and supports Quick Charge technology (Charging
adapter not included in the scope of delivery).
2.2 Scope of delivery
Wireless Quick-Charging Pad 15 W, Charging ca-
ble, User Manual
2.3 Operating Elements
See Fig. 1.
1 Non-slip surface
2 Charging interface
3 Smartphone holder
4 USB-C™ socket
5 USB-A plug
6 USB-C™ plug

3 Intended use

We do not permit using the device in other
ways like described in chapter „Description
and Function" or in the „Safety Instructions".
Use the product only in dry interior rooms. Not at-
tending to these regulations and safety instructions
might cause fatal accidents, injuries, and damages
to persons and property.
4 Preparation
1. Check the scope of delivery for completeness
and integrity.
2. Compare the specifications of all used devices
and ensure compatibility.

5 Connection and operation

1. Place the charging mat on a dust-free, level, ho-
rizontal surface.
2. Connect the USB-C™ socket of the charging mat
to a USB power source via the charging cable.
This can be either a 230 V USB charging adapter,
a 12/24 V car USB charger or the USB socket of a
PC (see Fig. 2).
The USB power source must support at least
5 V / 2 A. To use the fast charging mode (15 W), a
Quick Charge power adapter with 9 V / 2 A or
12 V / 2 A must be used.
3. Place a Qi standard compatible device on the
charging mat (see Fig. 3).
Charging your device is also possible with a pro-
tective cover, provided the cover does not contain
any metal parts and is not thicker than 6 mm.
4. Remove your device from the charging mat when
it is fully charged.
5. Disconnect all cable connections after use.
- 4 -
Pillmannstraße 12 | 38112 Braunschweig | Germany
60471
Goobay® by Wentronic GmbH