Fein GRIT GI75 Manual De Instrucciones página 16

en
16
Noise emission values.
A-weighted emission
pressure power level
measured at the work-
place L (re 20 μPa), in
pA
decibels
Measuring uncertainty
K , in decibels
pA
Measured A-weighted
sound power level L
wA
(re 1 pW), in decibels
Measuring uncertainty
K , in decibels
wA
Operating conditions
Speed (rpm)
Material
Dimension
Grinding belt
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear hearing protection!
Measured values determined in accordance with the
corresponding product standard (see last page in this
Instruction Manual).
Repair and customer service.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
When the machine's power supply cable is damaged, it
must be replaced using a specially prepared power sup-
ply cable, available from your FEIN customer service
agent.
The current spare parts list of this machine can be found
on the Internet under www.fein.com.
Daily maintenance
Blow out the ventilation slots (18) at the motor
housing and the marked locations with com-
pressed air (see Instruction label (27)).
Lubricate the machine daily (when in use) with
machine oil at the locations marked (see Instruc-
tion label (27)).
Check the drive disc (23) and the contact disc (21) for
wear and damage each time when replacing a grinding
belt. Have damaged parts replaced.
Loosen star-knob bolt (11).
Remove the chip/grinding-dust box (8) and dispose of
the metal dust.
Idle Sanding
80.5 94
4 4
90 100,5
2.5 2.5
3 000 3 000
– ST 37
– 8 x 40
GRIT by Fein
– 36Z
Before emptying, the contents of the chip/grinding-dust
box must have cooled down sufficiently and may only
be disposed of in suitable containers.
Mount the emptied chip/grinding-dust box again and
set the gap clearance of the grinding rest. (figure 1)
Tighten star-knob bolt (11).
Cleaning the exterior of the machine with compressed
air.
Lubricate the bearings of the tensioning device monthly
via the lubricating nipple (24).
If required, you can change the following parts your-
self: Grinding belt, spark guard
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your machine may include only a
part of the accessories described or shown in this
instruction manual.
Declaration of conformity.
This CE declaration is only valid for European Union
and EFTA (European Free Trade Association) countries
and only for products intended for the EU- or EFTA
market. After placing the product on the EU market the
UKCA mark loses its mark validity.
The UKCA declaration is only valid for the Great
Britain market (England, Wales and Scotland) and only
for products intended for the Great Britain market.
After placing the product on the Great Britain market
the CE mark loses its mark validity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
C-D1_IA, D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out machines and accessories should
be sorted for environment-friendly recycling.
Connection diagrams.
Type GI75, GI150
Type GI75 2V, GI150 2V
Type GI75 2H, GI150 2H
Type GI75 2H2V, GI150 2H2V
Page 104
Page 105
Page 106
Page 107