Idiomas disponibles
Idiomas disponibles
enter the 3 digits of the 1st user secondary
address (codes from 1 to 200) following
the procedure reported on the paragraph
"Entering codes and values";
press the button
to confirm the present
address and move to the 2nd user address;
an acknowledge tone will be heard;
enter the 3 digits of the 2nd user secondary
address and confirm by pressing button
proceed entering the 3rd and 4th second-
ary user addresses (if necessary) or press
twice the
to input the internal common
address;
enter the 3 digits that compose the internal
common address to the 4 new user
addresses (codes from 000 to 006) following
the procedure of the paragraph "Entering
codes and values".
Note: the internal common address has to
be unique and different from the address
eventually programmed on other intercoms
that has the same user address;
to press
to confirm; an acknowledge
tone will be heard and the yellow LED lights-
ON continuously;
continue with the next programming or exit
programming.
Programming addresses associated with
intercom buttons.
Buttons 1-6 can activate various services (each
identified by its address). By default they are
all empty.
Permitted values are:
- Address 000: (see table 3) Intercom call to
another user in the same flat;
- addresses 001-200: call to another user
- addresses 201-210: call to concierge unit;
- addresses 211-220: relay activation;
- addresses 231-253: connection to door unit,
without having been called. It is possible to
send the door lock release command and, by
unhooking the handset, activate the audio;
- address 255: deletion of previously entered
value.
The programming procedure is shown below.
After entering in programming mode:
a - keep pressed for more than 4 seconds the
button you wish to program; yellow LED
starts flashing;
b - enter the 3 digits of the code or address
you wish to store following the procedure
reported on the paragraph "Entering codes
and values";
c -press the button
; an acknowledge tone
will be heard and the yellow LED lights-ON
continuously;
repeat phases a-b-c to program other
buttons or exit the programming mode by
Table 3. Buttons used for intercom calls of max. 7 intercoms in the same apartment.
Master
Slave 1
button 1
000
slave 1 button 1
000
button 2
000
slave 2 button 2
000
button 3
000
slave 3 button 3
000
button 4
000
slave 4 button 4 000
button 5
000
slave 5 button 5
000
button 6
000
slave 6 button 6 000
hanging up the handset; yellow LED turns-
OFF.
Notes.
- In each button can be stored only one address.
Programming of floor call sending.
When the input terminals A1 and GN of the
intercom are closed by means of a button, the
floor call is activated (the intercom rings with
the melody programmed for this type of call,
without enabling the conversation). It is also
possible to send the same call to all slaves in
the same flat, without having to connect their
A1/GN terminals. To enable this choice (by de-
fault not enabled) it is necessary to:
after entering in programming mode, keep
pressed the button
seconds; yellow LED starts flashing;
keep pressed the button "1" for more than 4
seconds; yellow LED starts flashing quickly;
press the button "2" once to enable this
choice (you hear a sharp tone); within 2
seconds press the button "2" again to disable
it (you hear a low tone);
press the button "1" 8 times;
press the button
continue with the next programming or exit
programming.
Programming enabling reception of door
open signal.
Receiving of the door open signal and conse-
quent lighting of the yellow LED is factory-set
to be received only if the signal is forwarded
to your own address. To enable reception of
the signal intended for any address, proceed
as follows:
after entering in programming mode, keep
pressed the button
seconds; yellow LED starts flashing;
keep pressed the button "1" for more than 4
seconds; yellow LED starts quickly flashing;
press the button "1" 7 times;
press the button "2" once to enable (you
hear a sharp tone); within 2 seconds press
the button "2" again to disable (you hear a
low tone);
press the button "1" one time;
press the button
continue with the next programming or exit
programming.
Programming ringtones.
The intercom can play 4 different ringtones that
can be changed as indicated in the procedure
below. The default programming values and
the call sequence are shown in table 1.
All programming operations must be carried
out with the handset in idle position. Do not
Slave 2
Slave 3
master button 1
000
master button 1
slave 2 button 2
000
slave 1
button 2
slave 3 button 3
000
slave 3 button 3
slave 4 button 4
000
slave 4 button 4
slave 5
button 5
000
slave 5
button 5
slave 6 button 6
000
slave 6 button 6
enter programming like described in "Entering
the programming mode" paragraph but
proceed as listed below:
Keep pressed the button "1" for more than 4
seconds; the yellow LED turns ON and you
hear the ring tone that was programmed for
calls from external door station.
a - Press the button "1" repeatedly to select
the ring tone.
b - Press the button
to select the number of rings.
c - Press the button "1" as many times as the
desired number of rings (once = 1 ring; 4
times = 4 rings).
d - Press the button
to program the ring tone for intercom calls.
for more than 4
If you want to change the other two tone
rings (call from other user or floor call), you
must repeat steps a-b-c-d.
Pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
Adjusting the volume.
With the handset in idle position, you can
adjust 4 volume levels for all ring tones, as
to confirm;
indicated below:
press the button "1" for 4 seconds; the yellow
LED turns ON and you hear the external door
station ring tone;
hold the button
when you hear the desired volume;
pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
The volume levels are stored and will be used
for the next calls.
Return to factory defaults
To return to the factory settings, it is neces-
for more than 4
sary to:
enter programming mode following the
instructions described in the paragraph
"Entering programming mode",
press the following buttons in this se-
quence: 6, 5, 4, 3, 2 and 1;
the tone indicates that the default values
have been restored.;
exit programming. If new programming is
required, re-enter and perform the neces-
to confirm;
sary steps.
Slave 4
000
master button 1
000
master button 1
000
slave 1 button 2
000
slave 1
000
slave 2 button 3
000
slave 2 button 3
000
slave 4 button 4
000
slave 3 button 4
000
slave 5 button 5
000
slave 5 button 5
000
slave 6 button 6
000
slave 6 button 6
to confirm and go on
to confirm and go on
pressed and release it
Slave 5
Slave 6
000
master button 1
000
button 2
000
slave 1
button 2
000
000
slave 2 button 3
000
000
slave 3 button 4
000
000
slave 4 button 5
000
000
slave 6 button 6
000
Mi 2401/1
master
slave 1
slave 2
slave 3
slave 4
slave 5
- 11 -
