DWT SBH06-20 Manual Original página 25

Symbol
power tool designation
Power tools allow the following types of work to be per-
formed:
• drilling without impact (in wood, synthetic materials,
metal);
• impact drilling (in brick, concrete, natural stone);
• chiseling works (slotting cable channels in brick,
concrete, stone, removing old tiles, etc�);
• loosening and tightening threaded fasteners�
Power tool
components
Сhuck SDS PLUS
1
2 Dust protection casing
3 Fixing bush
4 Retainer *
5 Depth stop *
6 Additional handle *
7 Lock button
8 Function switch
9 Ventilation slots
10 Rotational direction switch
11 On / off switch
12 Lock-on button
13 Drill chuck key *
14 Gear rim chuck *
15 Screw *
16 SDS PLUS adapter *
17 Dust collector *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation
of power tool elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Meaning
Wear protective gloves�
Stepless speed control�
Do not dispose of the power
tool in a domestic waste
container�
DWT
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Additional handle (see fig. 1)
Always use the additional handle 6 when operating�
Additional handle 6 may be positioned as deemed
comfortable by the user�
• Loose additional handle 6 as shown in fig. 1.1
• Place additional handle 6 in desired position (see
fig. 1.2).
• Tighten additional handle 6 as shown in fig. 1.3
Depth stop (see fig. 2-3)
Use depth stop 5 to set a required drilling depth (see
fig. 2-3).
• Press and hold retainer 4 (see fig. 2.1).
• Move depth stop 5 to set a required drilling depth
(see fig. 2.2, 3).
• Release retainer 4 (see fig. 2.3).
Mounting / replacement of accessories (see fig. 4)
Borers SDS PLUS are able, due to the de-
signed features of the chuck SDS PLUS,
to travel freely to some extent� This causes
radial run-out at idle running that will be
automatically centred during the drilling� It doesn't
make any impact on the precision of bore drilling�
• Before installing the borer (chisel), clean it and lubri-
cate the shank with a thin layer of oil�
• When mounting borer (chisel):
• insert (slightly twisting) the borer (chisel) into the
chuck 1 (SDS PLUS) against stop (see fig. 4.1);
• test the borer (chisel) fixing by trying to remove it
from chuck 1 (SDS PLUS)�
• When removing borer (chisel):
• move fixing bush 3 back and hold it in this position
(see fig. 4.2);
• extract the borer (chisel) from the chuck 1
(SDS PLUS);
• release fixing bush 3 (see fig. 4.3).
Gloves are to be used when removing the
borer (chisel) from chuck 1 (SDS PLUS),
as the borer (chisel) may be dangerously
hot after long drilling.
Replacing the dust protection casing (see fig. 5)
Dust
the dust from entering the SDS PLUS
chuck. Never use your power tool with
a damaged dust protection casing 2 - if
damaged, it must be immediately replaced. You
can either do it on your own, or contact the DWT
service center.
• Move fixing bush 3 back and hold it in that position
(see fig. 5.1).
• Pull dust protection casing 2, and remove it (see
fig. 5.2).
English
Autogoods "130"
24
protection casing 2 prevents