Installation Instructions - Garmin GT41 Traditional Instrucciones De Instalación

12-pin Transducer Adapter Box

Installation Instructions

Mounting Location Considerations
Use the adapter to connect your 12-pin sounder to a compatible
bare wire, 12-pin, 8-pin, or 6-pin transducer.
• The adapter cable from the device should reach the
transducer connector on the sounder easily when the device
is mounted.
• The device should not be submerged in water.
• The device should be mounted at least 15.25 cm (6 in.) from
a source of electrical interference, such as a motor.
• When a mounting surface is unsuitable for screws, you must
secure the device to a structure using cable ties (not
included).
Tools Needed
1
• Drill and 3.2 mm ( / in.) drill bit
8
• #2 Phillips screwdriver
• 3 mm flat screwdriver
• Cable ties (optional)
• Wire cutter
• Wire stripper
13
• 21 mm ( / in.) wrench
16
• 15 mm (or adjustable) wrench (optional)
Mounting the Device
1
1
Using the 3.2 mm ( / in.) bit, drill the pilot holes.
8
2
Insert the screws into the pilot holes, but do not tighten them
flush with the surface.
3
Place the adapter on the screws and slide it into place.
4
With the adapter unmounted, connect the wires.
5
Tighten the screws until the device is securely fastened to the
surface.
Connecting the Device to a Transducer
Preparing the Transducer to Connect to the Adapter
Before you can begin the installation, you must check your
transducer compatibility. Water speed wheels are not supported
on the 12-pin sounder connector.
1
For a transducer with a 12-pin, 8-pin, or 6-pin connector, cut
off the connector cable as close to the connector as possible.
Garmin 12-pin Transducers
Garmin Part Description
010-12089-00 Garmin GT30
SideVü/DownVü
010-12089-10
010-12089-11
010-12220-00 Garmin GT40
Traditional/SideVü/
DownVü
2
1: Shield/ 2: 3: GID 4:
Ground Temp + XID
Bare White Green NA
Bare White Green NA
2
Feed the cut end of the cable
side of the housing and pull it out through the other side.
3 Use the wire stripper to remove about 90 mm (3
outer cable jacket
4
Use the wire stripper to remove about 6 mm (
insulation from each internal wire
NOTE: Tinning the stripped wires is recommended.
5
For transducers without a temperature sensor, you can use a
15 mm (or adjustable) wrench to connect a separate
temperature sensor through the nut
the housing (optional).
Connecting the Transducer Wires to the 12-pin
Adapter
1 Using a 3 mm flat screwdriver, connect the transducer wires
to the wire block in the 12-pin adapter as shown in the wiring
block table.
NOTE: You can consult the wire color tables to identify the
wire functions for some Garmin
Wire Block Number
1
2
3
4
5
6
7
8
9
10
11
12
2
When the wire connections are secure, use a 21 mm
13
( / in.) wrench to tighten the nut around the transducer
16
cable.
3
Place the lid on the adapter and secure it with the four
captive Phillips screws.
Specifications
Specification
Dimensions (W x H x L)
Cable length
Water rating
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to
/waterrating.
Wiring Block Tables
5: Right 6: Right 7: Down
- / Low + / Low - / Hi
Depth - Depth + Depth -
Yellow Brown Black
Yellow Brown Black
through the nut
and foil shield.
.
on the bottom side of
and Airmar
®
Wire Function
Shield/Ground
Temp +
GID
XID
Right - / Low depth -
Right + / Low depth +
Down - / Hi depth -
Down + / Hi depth +
Left +
Left -
Reserved 1
Reserved 2
Measurement
59.1 x 48.97 x 104 mm (2.3 x 1.9 x
4.1 in.)
61 cm (24 in.)
IEC 60529 IPX7*
www.garmin.com
8: Down 9: Left + 10: 11:
+ / Hi Left - Reserved 1
Depth +
Blue Orange Red NA
Blue Orange Red NA
Installation Instructions
on the
1
/ in.) of the
2
1
/ in.) of the
4
transducers.
™
12:
Reserved 2
NA
NA