Assembly; Commissioning; Maintenance; Storage - Scheppach HD12 Traducción Del Manual De Instrucciones Original

m Attention!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

7. Assembly

For packaging reasons, your machine is not com-
pletely assembled.
• Attach the side covering loosely to the base frame
using flat-head screws M8 x 40 mm and screw
nuts. Do not tighten completely. fig. 2, 3
• Attach the cross member to the side covering left
and right with flat-head screws M 8 x 12 and screw
nuts. fig. 4, 5
• Remove all screws and nuts from the housing.
• Attach the housing to the side coverings using flat-
head screws M5 x 20 and screw nuts. Securely
tighten all nuts. fig. 6
• Slide the clamping strip through the loops on the fil-
ter bag and fix the filter bag on the container. fig. 7
• Position the support bar into the housing and hang
the filter bag from it. fig. 1
• Attach the sawdust bag to the lower air ventilator
using the clamping strip. fig. 7
• Attach the extraction hose to the nozzle on the
housing and affix it with a hose clamp. fig. 8
• Attach the hose coupling to the other end of the
hose using a hose clamp. fig. 9
The extraction system should be cleaned every time
the sawdust bag is changed.
Damaged filters and bags must be immediately
changed in order to keep the amount of dust that es-
capes into the work environment as low as possible.

8. Commissioning

Observe the safety instructions before the commis-
sioning. The data on the motor type plate (voltage
and frequency) must match the mains voltage and
frequency.
After connecting to the mains, the extraction system
is ready for operation.

9. Maintenance

For all maintenance and cleaning work, turn off the
motor and pull out the mains plug.
• Installation, repairs and maintenance work on the
electrical equipment may only be carried out by
electricians.
• For constant performance, periodically shake out
filter bag vigorously. Between cleanings, beating
the bag with the hand several times is sufficient.
• The sawdust bag must be replaced at the latest
when the sawdust is within 10 cm of the housing
collar.
18 | GB
 www.scheppach.com /  [email protected] /  +800 4002 4002
Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*: carbon brushes, filter bag, sawdust
bag, extraction hose, nozzle attachments; V-belt
* may not be included in the scope of supply!
Special accessories
Filter bag .......................................... art. no. 3906301013
Returnable sawdust bag 20 pcs. .... art. no. 75001500

10. Storage

Store the device and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
30 ˚C. Store the electric tool in its original packaging.

11. Electrical connection

Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
The electrical motor installed is connected and ready
for operation. The connection complies with the ap-
plicable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these regu-
lations.
Important information
Damaged electrical connection cables
If the power cable is damaged, it must be replaced
by the manufacturer or their service department or
a similar qualified person in order to avoid hazards.
The insulation on electrical connection cables is of-
ten damaged.
Causes are:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables
must not be used and are life-threatening due to
insulation damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.