Technical Data - Rockwell RK2516 Manual De Instrucciones

Multi-PurPose saw

tecHNical Data

Rated Voltage
No load speed
Stroke length
Max cutting depth in
Machine weight
oPeratiNG iNstructioNs
Note: before using the tool, read the
instruction book carefully.
cHarGiNG ProceDure
1. cHarGiNG your Battery PacK
warNiNG: The charger and battery pack are
specifically designed to work together so do
not attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery pack
connections because an electrical failure and hazard
will occur.
2. BeFore usiNG your corDless tool
your battery pack is uNChaRGEd and you must charge
once before use. When you charge the new battery
or one which has not been used for long periods of
time, it may not reach full charge until after you have
discharged it fully in use and recharged it several times.
3. How to cHarGe your Battery PacK (see FiG. a)
1) Plug the charger into an appropriate outlet. The light
will be green.
2) insert the battery pack into the charger, the light will
be red to indicate the charging process has started.
3) On completion of charge, the light will turn green.
The pack is now fully charged, unplug the charger
and remove the battery pack.
warNiNG: when battery charge runs out
after continuous use or exposure to direct
sunlight or heat, allow time for the battery to cool
down before re-charging to achieve the full charge.
4. to reMove or iNstall Battery PacK (see FiG. B)
Locate buttons on side of battery pack and depress both
sides to release battery pack from your tool. Remove
battery pack from your tool. after recharge insert the
12 V
2200 spm
Wood
aluminum 1- 3/4˝
Steel
2.6 lbs
battery pack into the battery port. a simple push and
slight pressure will be sufficient.
aDJustMeNt
This tool functions as a combination jigsaw and
5/8˝
reciprocating saw. use the pivot release lever (4) to
change the configuration.
2˝
Lift up the pivot release lever fully, until it cannot be
lifted further. (See fig. C)
5/32˝
Rotate the front portion of the tool into any of the SiX
positions (0, 18, 36, 54, 72 and 90deg) (See fig. d).
Restore the pivot release lever.
in Position i (0deg), this tool can be used as a
reciprocating saw.
in Position Vi (90deg), this tool can be used as a jigsaw.
warNiNG!
when adjusting the tool, you can only hold
the foot plate as shown in Fig.e1. Never hold the
pivot head as shown in Fig. e2, e3.
warNiNG!
• To avoid being pinched, keep hands away from the
hinge when changing positions.
• To avoid tool being turned on accidentally, remove the
battery pack from the tool.
rePlaciNG / iNsertiNG tHe saw BlaDe
Before any work on the machine itself, remove
the battery.
The blade should extend past the foot plate and the
thickness of the workpiece during the cut. Select the
blade best suitable for the material to be cut and use the
shortest blade suitable for the thickness of the material.
warNiNG! cut hazard. blade breakage may
occur if the blade does not extend past the foot
plate and the workpiece during the cut. increased risk of
personal injury, as well as damage to the foot plate and
workpiece may result.
cautioN: Remove the battery pack to prevent switch
actuation before making any adjustments or removing
or installing attachments or accessories.
—iNsertiNG tHe saw BlaDe (see FiG. F-H)
wear protective gloves when assembling the saw
blade. Contact with the saw blade can lead to injuries.
you can only use the t-shank blade type shown
in Fig F.
The machine is equipped with a tool-free blade holder
(7). This makes possible easy and quick changing of the
saw blade without any additional tools.
Rotate the ring counterclockwise and hold in position.
eNG
9