Before Use; During Use; After Use - SKIL MASTERS F0157470 Serie Manual Original

e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
• This tool should not be used by people under the age of
16 years
• This tool is not suitable for wet sanding
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Do not continue to use worn, torn or heavily clogged
sanding discs

BEFORE USE

• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
(tools with a rating of 230V or 240V can also be
connected to a 220V supply)
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• The noise level when working can exceed 85 dB(A); wear
ear protection
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• When sanding metal, sparks are generated; do not use
dustbox and keep other persons and combustible
material from work area

DURING USE

• Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
• Do not touch the moving sanding disc
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Backing pads
- never run the tool without backing pad A
! replace damaged backing pads immediately
(loosen/fasten 4 pad screws B)
! unplug tool before removing/mounting backing
pads
• Mounting sanding discs
- simply press sanding disc C onto backing pad with
perforation in sanding disc corresponding with
perforation in backing pad
- if necessary, clean backing pad first
! the dust suction requires the use of perforated
sanding discs
• Dust suction 4
- empty dustbox D regularly for optimal dust pick-up
performance
- remove dustbox D by pushing knob E to the left and
hold it in that position while pulling dustbox D
backwards
- mount dustbox D by sliding it back until it clicks into
place
! do not use dustbox when sanding metal
• On/off
- before switching on the tool, you should place it with
the entire sanding surface on the workpiece
- when switching on, do not apply too much pressure on
the tool
- switch on/off the tool by pulling/releasing trigger F
! be aware of the sudden impact when the tool is
switched on
! before switching off the tool, you should lift it
from the workpiece
• Switch lock
- pull trigger F 2
- press knob G 2 with your thumb
6