THOMSON ROC5404 Manual De Utilización página 7

F01_GB_ROC5404
All manuals and user guides at all-guides.com
Programming a sequence
of commands (Macro)
The MACRO key in coordination with one of the keys
1, 2, or 3, allows the programming and memorisation
of up to 3 command sequences (the automatic and
successive pressing of several keys of your choice). Thus
any sequence of key commands can be reduced to
merely 2 commands (MACRO key + key 1, 2, or 3).
For example after programming, by pressing MACRO
then key 1 you could turn on your television set, turn on
your satellite or cable receiver, zap to a preferred
channel, turn on your video cassette recorder and start
a recording session (providing a cassette was
previously loaded). You can memorise a sequence of
10 commands with each key 1, 2, or 3.
Note: during the programming of a macro, the time
between each step is limited to a few seconds. This
leaves little time for reading the instructions and then
carrying them out. If the mode indicator light blinks
and then goes out, it is because this time limit has
been exceeded, you must start again from step 1.
To record a MACRO:
1. Press and hold down the S (setup) key until a (TV,
VCR, ...) mode key blinks 3 times and remains lit
(after 2 or 3 seconds).
2. Release the S key.
3. Press the MACRO key once. The mode key blinks.
4. Press once the 1, 2 or 3 key which you are going
to use to memorise the sequence.
5. Press once on the (TV, VCR, ...) mode key of the
first device you wish to control (the first key must
always be a mode key.)
6. Successively press the keys corresponding to the
commands you wish to send to the device(s) (9 keys
maximum, including other mode keys). The mode
key blinks when each key is pressed.
7. Memorise your key sequences by pressing the
MACRO key once. The mode key is no longer lit
and your Macro is complete.
Note: a sequence will be automatically memorised
after the tenth key press (counted from the mode key)
and the mode key light will go out.
To use a MACRO:
Press the MACRO key once and, within 20 seconds,
press the 1, 2 or 3 key you used to memorise the
sequence.
Note: when running a Macro (which takes a few
seconds), ensure that the remote control is aimed at
the device being controlled.
Remarks:
• The default time between sending 2 commands when
using a macro is half a second.. However, it is
possible that you will need to add longer periods in
your sequence in order to allow enough time for
certain devices to turn themselves on. To lengthen the
time period between 2 commands, press once on the
PAUSE key and then press one of the keys from 1 to
9 in order to insert a pause from 1 to 9 seconds.
• The first key in a sequence must always be a ( TV ,
VCR , ...) mode key.
Note: the indications TV , VCR , DVD (below keys 1 ,
2 , 3 ) are only an aid to memory. You may decide, for
example, to memorise a MACRO for the television
set using key 1 , etc.
Deleting a MACRO:
1. Press and hold down the S key until the (TV,
VCR...) mode key blinks 3 times and then remains
lit (after 2 or 3 seconds).
2. Release the S key.
3. Press once on the MACRO key. The mode key
begins to blink.
4. Press once the 1, 2 or 3 key that represents the
sequence to delete.
5. Press and hold down the S (setup) key. The mode
key light goes out and the sequence is now deleted.
9/12/04 15:06
3
Page 3
Other function:
All modes OFF
If the B B key is pressed twice within one second, and is
held down for more than 2 seconds the second time,
then the remote control will send the OFF code for all
modes.
Controlling volume in satellite
and cable mode
Since some satellite and cable receivers have no
volume control, the ROC 5404 remote control allows
you to control the television's volume in satellite or cable
mode. For satellite systems with a volume control, it is
possible to choose the set that the MUTE (
VOL keys will control in each of these modes: the
television volume or the volume of the satellite or cable
receiver.
To choose, proceed as follows:
1. Press the TV key (the remote control must be in TV
mode for this procedure).
2. Hold down the S key until the last mode selected
(TV) blinks 3 times and then remains lit.
3. Release the S key.
4. Press the MUTE ( ) key for around 8 seconds.
The TV mode indicator light will blink and go out
for about 8 seconds before blinking once; at this
point, release the MUTE (
5. If the remote control previously controlled the
television volume in SAT or CBL mode, it will now
control the volume of the satellite or cable receiver;
if it previously controlled the volume of the satellite
or cable receiver, it will now control the television
volume.
The NAVILIGHT system
The THOMSON NAVILIGHT system allows you easy
access to the settings of your television (TV) or video
recorder (VCR) including this feature.
1. Switch on the set you want to control.
2. Press the key corresponding to the type of set you
want to use (TV, VCR, or SAT). In the VCR
position, make sure that the AV mode is activated for
the TV set (the SCART socket must be selected).
3. Press key MENU once.
4. Navigate through the setting menus with the keys up,
down, left, right (p, q, t, u).
5. Validate with OK.
6. To leave the menus, press key EXIT once.
You can contact THOMSON by dialling:
0871 712 1312
(For Great-Britain,
all calls will be charged 0,£10 / mn)
www.thomson-europe.com
ROC5404 / GB - bj - XX / bei - rst / 12-2004
) and
) key.