Tabla de contenido
Idiomas disponibles
Idiomas disponibles
FUELING
ENGINE
_
WARNING:
Remove fuelcap slow-
ly
when refueling.
HELPFUL
TIP
l
roobtainthecorrecteilmix
I
lJ ratio,
pour 3.2 ounces
of |
'/ 2-cycle
synthetic
eft into
I
one gallon of fresh gas.
J
This
engine
is
certified
to
operate
on
unleaded
gasolh_e.
Before
operation,
gasoline
must be mixed with a good quality
synthetic
2-cycle
air-coo_ed
engine
oil
designed
to be mixed
at a ratio
of 40:1.
Poulan/WEED
EATER brand synthetic
oil is
recommended.
A 40:1 ratio is obtah_ed by
mixing 3.2 ounces
(95 ml) of oil with 1 gaIIon (4
liters) of unleaded gasotine.
Included with this
saw is a 3.2 ounce container of PoulanANEED
EATER brand synthetic
oil.
Pour the entire
contents
of this container
into
1 gallon of
gasoline to achieve the proper fuel mixture.
DO NOT USE automotive
or boat oil. These
oils will cause engine damage.
When mixing
fuel follow
the instructions
printed
on the
container.
Always read and follow the safety
rules
listed
under
HANDLE
FUEL
WITH
CAUTION.
BAR
AND
CHAIN
LUBRICATION
The bar and chain require
continuous
lubri-
cation.
Lubrication
is provided
by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quicMy ruin the bar and
chain.
Too littIe oil will cause
overheating
shown by smoke coming from the chain and/
or discoloration
of the bar.
In freezing
weather oil witl thicken,
making it
necessary
to thin bar and chain
oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
kerosene.
Bar and chain oil must be free
flowing for the oil system to pump enough oil
for adequate
lubrication.
Genuine
Poulan_;
bar
and
chain
oil
is
recommended
to protect
your
unit against
excessive
wear
from
heat
and
friction.
Poulan_;
oil resists
high temperature
thinning.
If Poulan_;
bar and chain oil is not
available,
use a good grade SAE 30 oil.
• Never use waste oil for bar and chain lubri-
cation.
• Always
stop the engine
before removing
the oil cap.
IMPORTANT
Experience
indicates
that alcohol-blended
fuels
(called
gasohol
or using
ethanol
or
methanol)
can attract moisture
which
leads
to separation
and formation
of acids during
storage.
Acidic
gas can damage
the fuel
system
of an engine while
in storage.
To
avoid
engine
problems,
the
fuel
system
should
be emptied
before
storage
for 30
days or longer.
Drain the gas tank, start the
engine and let it run until the fuel lines and
carburetor
are empty.
Use fresh fuel next
season.
See STORAGE
section
for addi-
tional information.
mlWARNING:
The chain
must not
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR
ADJUSTMENT
within
this
manual. Avoid contact with the muffler. A hot
muffler can cause serious
burns.
To stop
the engine
move
the ON/STOP
switch
to the STOP position.
To start the engine
hold the saw firmly on the
ground as illustrated.
Make sure the chain is
free to turn without contacting
any object.
Use only 15 - 18 inches
(38 - 45 em) of
rope per pull.
Hold saw firmly while pulling
starter rope.
Starter rope handle
l{ . _,_\-_
_
Left hand
_,
("_
_f,;I
_l_--
on front
Right foot through
rear handle
IMPORTANT
POINTS
TO REMEMBER
When pul_ing the starter rope, do not use the full
extent of the rope as this can cause the rope to
break.
Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
For cold weather
starting,
start the unit at
FULL CHOKE;
allow the engine to warm up
before squeezing
the throttle trigger.
NOTE:
Do not cut material
with the choke/
fast idle lever at the FULL CHOKE
position.
HELPFUL TIP
J
if y°ur engine still d°es not
I
start
after following
these
I
instructions,
please
carl
1 - 800- 554 - 5723.
STARTING
A
COLD
ENGINE
(or
warm
engine
after
running
out
of
fuel):
NOTE:
In the following
steps,
when the
choke/fast
idle lever is pulled out to the full
extent, the correct throttle setting for starting
is set automatically.
ON/STOP
SWITCH
(_ .SIDE VIEW)
ON
_
" .,"."
STOP
1. Move ON/STOP
switch
to the ON posi-
tion.
2.
Slowly press
primer bulb 6 times.
Tabla de contenido
