Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PROGRAM MEMORY MANAGEMENT
PROGRAM MEMORY MANAGEMENT
(S-P)". Having selected the option, select the program number with the main selector and confirm the action by
pressing the same selector.
The recovered data can be edited and will be saved as the current program, but the original program in the memory will
The recovered data can be edited and will be saved as the current program, but the original program in the memory will
The recovered data can be edited and will be saved as the current program, but the original program in the memory will
not be changed, being safeguarded from accidental changes.
safeguarded from accidental changes.
DATA MENU
Enter menu mode and select . In this menu, we have the possibility to read the wire consumption data and the worked
Enter menu mode and select . In this menu, we have the possibility to read the wire consumption data and the worked
Enter menu mode and select . In this menu, we have the possibility to read the wire consumption data and the worked
hours of the machine.
The wire consumption data will be displayed in m and cm. You can reset this value at any moment using the option
The wire consumption data will be displayed in m and cm. You can rese
from the menu. If you don't reset the value manually, this value will be reset automatically when it arrives to 600m.
from the menu. If you don't reset the value manually, this value will be reset automatically when it arrives to 600m.
from the menu. If you don't reset the value manually, this value will be reset automatically when it arrives to 600m.
The operating time value is displayed in hours and minutes (hhhh.mm) and cannot be reset. Th
The operating time value is displayed in hours and minutes (hhhh.mm) and cannot be reset. Th
The operating time value is displayed in hours and minutes (hhhh.mm) and cannot be reset. The value on this time
meter increases with the real welding time.
meter increases with the real welding time.
RESETTING PARAMETERS TO DEFAULT VALUES
RESETTING PARAMETERS TO DEFAULT VALUES
All operating program data can be reset to the default value, which is useful for correcting problems caused by
All operating program data can be reset to the default value, which is useful for correcting problems caused by
All operating program data can be reset to the default value, which is useful for correcting problems caused by
unintentionally altered parameters. To reset, enter the menu and select "ini". When you press the master control, you
will be asked to confirm this action. With the main control, select "YES" and all data of the current operating program
will be asked to confirm this action. With the main control, select "YES" and all data of the current operating program
will be asked to confirm this action. With the main control, select "YES" and all data of the current operating program
will be reset.
INFORMATION OF SYSTEM VERSION
INFORMATION OF SYSTEM VERSION
In the menu option, you can check the system version information.
menu option, you can check the system version information. Indicates the power unit firmware release and
firmware release of the user interface
MIG-MAG WELDING OPERATIONS
WELDING OPERATIONS
For most of the materials, you will have to connect the negative pole to the work piece and the positive pole to the torch.
For most of the materials, you will have to connect the negative pole to the work piece and the positive pole to the torch.
For most of the materials, you will have to connect the negative pole to the work piece and the positive pole to the torch.
For cored wires without gas (OP130, OP131, OP132 and OP133), you will have to connect the cables in reversed
For cored wires without gas (OP130, OP131, OP132 and OP133), you will have to connect the cables in reversed
For cored wires without gas (OP130, OP131, OP132 and OP133), you will have to connect the cables in reversed
polarity.
WIRE FEEDING SYSTEM
The wire feeding system must be prepared with the suitable options for the material used. You must install the
The wire feeding system must be prepared with the suitable options for the material used. You must install the
The wire feeding system must be prepared with the suitable options for the material used. You must install the
appropriate rollers for the material in use and set the rollers pressure to the minimum, so that the wire is pulled tig
appropriate rollers for the material in use and set the rollers pressure to the minimum, so that the wire is pulled tig
appropriate rollers for the material in use and set the rollers pressure to the minimum, so that the wire is pulled tightly,
but can skid if there is a blockage in the wire feed guide.
but can skid if there is a blockage in the wire feed guide.
Follow the procedure below for set the proper rollers pressure:
Follow the procedure below for set the proper rollers pressure:
the option, select the program number with the main selector and confirm the action by
the option, select the program number with the main selector and confirm the action by
Example: 71h 30 minutes
To reset, enter the menu and select "ini". When you press the master control, you
To reset, enter the menu and select "ini". When you press the master control, you
In MANUAL mode, the machine could be set in a non proper way
MANUAL mode, the machine could be set in a non proper way.
MANUAL mode, the machine could be set in a non proper way
The machine can store any program in
The machine can store any program in
memory with all data, both primary and
memory with all
secondary.
To manage the reading/writing of these
To manage the reading/writing of these
programs, select the program menu (enter
programs, select the program menu (enter
menu mode and select "Pro"). After that,
menu mode and select "Pro"). After that,
you can choose between the options "read
you can choose between the options "read
a program (L-P)" or "save a
a program (L
t this value at any moment using the option
ATTENTION
power unit firmware release and the
program
32
Capítulos
Tabla de contenido
