Insert The Batteries - TFA 30.3060.01.IT Instrucciones De Uso

TFA_No. 30.3060_Anleitung 02.06.2015
KLIMA@HOME - Wireless thermo-hygrometer
Important information on product safety!
• Do not place your device near extreme temperatures, vibrations or shocks.
• Protect it from moisture.
• The transmitters are protected against splash water, but they are not watertight. Would you like
to use the transmitters in the outdoor area, choose a shady and dry position for the transmitters.
5. Elements
5.1 Basic station (Receiver)
A: Display (Fig. 1):
Upper display
A 1: Symbol for indoors
A 2: Indoor temperature
A 3: Humidity
A 4: WeatherHub symbol
A 5: Comfort level symbol
A 6: Time with seconds
A 7: DCF symbol, date
Display below for transmitter 1-3
A 8: Transmitter reception symbol
A 9: Temperature and humidity
B: Buttons (Fig. 1):
B 1: SET button
B 2: + button
B 3: - button
B 4: CH button
C: Housing (Fig. 1+2):
C 1: Strip for labeling the transmitter sites
C 2: Wall hanging hole
C 3: Battery compartment
C 4: Stand (removable)
5.2 Transmitter (Fig. 3):
D: Display:
D 1: Temperature and humidity in sequence
E: Housing:
E 1: Battery compartment (screwed)
E 2: Device for wall mounting or table standing
E 3: Serial number (printed on the back)
14
16:58 Uhr Seite 8
KLIMA@HOME - Wireless thermo-hygrometer
6. Getting started

6.1 Insert the batteries

• Place the instruments on a desk with a distance of approximately 1.5 meter. Avoid getting close to
possible interference sources (Electronic devices and radio installations).
1. Open the screwed battery compartment of the first transmitter.
2. Insert two new batteries 1,5 V AA, polarity as illustrated.
3. On the display appear the measured temperature and humidity in sequence.
4. Close the battery compartment carefully.
• Repeat step 1-4 to install the other two transmitters.
• Open the battery compartment of the basic station and insert three new batteries 1.5 V AA, polarity
as illustrated.
• All LCD segments will be displayed briefly.
• Close the battery compartment again.
6.1.1 Reception of the transmitters
• After the batteries are inserted the transmitters will automatically transmit the measured values.
The radio controlled symbol will be flashing on the lower display.
• Each transmitter has its own serial number (four digits, alphanumeric), printed on the backside.
The serial number appears briefly on the display after inserting the batteries. As soon as the basic
station has received the transmitter, on the display of the basic station also appears briefly this
serial number.
• If the reception of the measured values fails, "- -" appears on the display. Check the batteries and
try it again. Check if there is any source of interference.
• As soon as the basic station received the radio-controlled time, you can start the initialization
manually. Choose the respective transmitter by pressing the CH button on the basic station Press
and hold the CH button for three seconds. The basic station tries to receive the measured values.
6.2 Reception of the DCF frequency signal
• After the main device has searched for the transmitters,the device begins to search the DCF signal
(radio controlled clock signal) and the DCF reception symbol will be flashing.
• When the time code is received successfully after 5-8 minutes, the radio-controlled time, the date
and the DCF symbol are displayed steadily in the display.
• The DCF reception always takes place hourly between 1:00 and 5:00 o'clock in the morning. If the
reception is not successfully received until 5:00 o'clock, the next receive operation is again at 1:00
o'clock in the morning.
• There are three different reception symbols:
flashing - reception is active
stays - reception is very good
No symbol - no reception / manual time set
• If the clock cannot detect the DCF-signal (for example due to disturbances, transmitting distance,
etc.), the time can be set manually. The DCF symbol disappears and the clock will then work as a
normal quartz clock. (see: Manual settings).
15