ETL-ES-Turbo Swirl CFL-WH10 COnSEjOS dE SEGuridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, MONTE EL VENTILADOR EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES”, Y UTILICE LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR. LA MAYORÍA DE LAS CAJAS DE EMBUTIR UTILIZADAS NORMALMENTE PARA ARTEFACTOS DE ILUMINACIÓN NO SON ADECUADAS PARA VENTILADORES Y DEBERÍAN SER REEMPLAZADAS.
Página 5
ETL-ES-Turbo Swirl CFL-WH10 FEaTurES CaraCTEríSTiCaS DOWNROD VAULTED CEILING INSTALLATION INSTALLATION FLUSH MOUNT INSTALLATION INSTALACIÓN CON INSTALACIÓN PARA INSTALACIÓN AL RAS VARILLA VERTICAL CIELORRASOS ABOVEDADOS May require a longer downrod For low ceilings For normal ceilings (sold separately) Para cielorrasos bajos Para cielorrasos normales Podría requerir una varilla vertical más larga...
ETL-ES-Turbo Swirl CFL-WH10 PrEParinG FOr inSTaLLaTiOn anTES dE La inSTaLaCión Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
ETL-ES-Turbo Swirl CFL-WH10 MOunTinG BraCKET inSTaLLaTiOn inSTaLaCión COn SOPOrTE dE MOnTajE Remove the screws from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the canopy. Rotate the mounting bracket and remove from the canopy.
Página 8
ETL-ES-Turbo Swirl CFL-WH10 MOunTinG BraCKET inSTaLLaTiOn MOunTinG OPTiOnS inSTaLaCión COn SOPOrTE OPCiOnES dE MOnTajE dE MOnTajE Choose a MOunTinG OPTiOn Elija una OPCión dE MOnTajE FLuSH MOunT OPTiOn If flush mount option is selected, proceed to page 9, step 6.
Página 9
ETL-ES-Turbo Swirl CFL-WH10 FLuSH MOunT OPTiOn OPCión dE inSTaLaCión aL raS For flush mount option, raise fan assembly and place onto hook from mounting bracket into a closed hole on the canopy. This will allow for hands free wiring. Guide motor wires through the base of the canopy as shown and attach canopy PrOCEEd dirECTLy TO PaGE 14 FOr WirinG OPTiOnS.
Página 10
ETL-ES-Turbo Swirl CFL-WH10 nOrMaL dOWnrOd OPTiOn EXTEndEd dOWnrOd OPTiOn OPCión COn VariLLa VErTiCaL Para OPCión COn VariLLa VErTiCaL CiELOrraSO nOrMaL MÁS LarGa Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod.
Página 12
ETL-ES-Turbo Swirl CFL-WH10 EXTEndEd dOWnrOd OPTiOn OPCión COn VariLLa VErTiCaL MÁS LarGa Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod.
ETL-ES-Turbo Swirl CFL-WH10 MOunTinG MOnTajE Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. With bracket holding fan assembly, make electrical connections using the following step for wiring instructions.
Página 14
ETL-ES-Turbo Swirl CFL-WH10 WirinG OPTiOnS OPCión dE CaBLEadO PuLL CHain WirinG OPTiOn WaLL COnTrOL WirinG OPTiOn Follow diagram above to make wiring connections for fan pull chain control. Follow diagram above to make wiring connections for wall control operation. OPCión dE CaBLEadO Para CadEniLLa dE TirO OPCión dE CaBLEadO Para COnTrOL dE ParEd...
ETL-ES-Turbo Swirl CFL-WH10 SECurE TO CEiLinG aSEGurE EL VEnTiLadOr aL CiELOrraSO For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores con varilla vertical, deslice el dosel hacia arriba hasta el soporte de montaje. The canopy has two mating slots (1) and two mating holes (2). Position both slots on canopy directly under and in line with two screws in the mounting bracket (3). Lift the canopy, allowing the two screws to slide into the mating slots.
ETL-ES-Turbo Swirl CFL-WH10 BLadE inSTaLLaTiOn inSTaLaCión dE LaS PaLETaS Attach blade assembly to motor using the screws and washers provided. Tighten screws Attach blade brackets to blades using the blade bracket screws (1), securely. fabric washers (2) and nuts (3).
ETL-ES-Turbo Swirl CFL-WH10 LiGHT FiXTurE inSTaLLaTiOn inSTaLaCión dEL arTEFaCTO LuMinOSO Install bulb (included). Attach glass to light fixture by inserting neck of glass into light fixture, keeping two spring clips inside the neck of the glass. Pull the glass shade toward the third spring clip.
ETL-ES-Turbo Swirl CFL-WH10 OPEraTiOn and MainTEnanCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off.
ETL-ES-Turbo Swirl CFL-WH10 OPEraCión y ManTEniMiEnTO Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado.