Idiomas disponibles
Idiomas disponibles
Tabla de contenido
π
PALLET TRUCKS
MODEL
Capacity
Max. Fork Height
Min. Fork Height
Fork Length
Width Overall Forks
Fork Wheel Diameter
Steering Wheel Diameter
Net Weight
WARNING! Operator must read and understand
instructions here and on truck prior to use.
On the handle of the pallet truck, you will find the control
lever, which can be set in three positions.
(See Figure 1)
Figure 1
- DOWN = to lower the forks
- NEUTRAL = to move the load
- UP = to raise the forks
PAGE 1 OF 6
1-800-295-5510
uline.com
TECHNICAL DATA
H-1043
H-1193
(Lbs.)
5,500
(In.)
(In.)
(In.)
48
(In.)
27
21
(In.)
(In.)
(Lbs.)
186
176
H-1484
H-1366
H-1779
7.5
3.0
36
27
21
27
3" Polyurethane
7" Polyurethane
173
160
243
OPERATION
1.
If the forks elevate while pumping in the NEUTRAL
position, turn the setting screw clockwise until
pumping the handle does not raise the forks and the
NEUTRAL position functions correctly.
2. If the forks descend while pumping in the NEUTRAL
position, turn the setting screw counter-clockwise until
the forks do not lower.
3. If the forks do not descend when the control lever is
in the DOWN position, turn the setting screw clockwise
until raising the control lever lowers the forks. Then
check the NEUTRAL position as per steps 1 and 2.
4.
If the forks do not lift while pumping in the UP position,
turn the setting screw counter-clockwise until the forks
elevate while pumping in the UP position. Then check
the NEUTRAL and DOWN position as per steps 1, 2
and 3.
NOTE: When viewing the truck from the handle
side, the setting screw is located on the right
side of the pump above the right wheel. The
truck will lower faster or slower depending on
how far in or out the screw is adjusted.
For Spanish, see pages 4-6.
Para Español, vea páginas 4-6.
H-2640
H-1365
H-1780
3,300
5.6
2.0
72
21
27
2" Steel
6" Polyurethane
230
191
203
H-1781
48
21
33
226
0312 IH-1043
Tabla de contenido
Manuales relacionados para Uline H-1043
Resumen de contenidos para Uline H-1043
- Página 1 For Spanish, see pages 4-6. Para Español, vea páginas 4-6. π 1-800-295-5510 uline.com PALLET TRUCKS TECHNICAL DATA MODEL H-1043 H-1193 H-1484 H-1366 H-1779 H-2640 H-1365 H-1780 H-1781 Capacity (Lbs.) 5,500 3,300 Max. Fork Height (In.) Min. Fork Height (In.) Fork Length (In.)
- Página 2 MAINTENANCE DOWN position and move the handle up and down several times. Please check the oil level every six months. The oil DAILY CHECK AND MAINTENANCE capacity is about 0.3L. Restore the fluid level in the reservoir to 5mm below the top; this must be Daily checks of the pallet truck can limit wear and tear done with the forks in the DOWN position.
- Página 3 NOTE: Do not attempt to repair the pallet truck unless you are trained and authorized to do so. π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 1-800-295-5510 uline.com PAGE 3 OF 6 0312 IH-1043...
-
Página 4: Datos Técnicos
π 01-800-295-5510 uline.mx PATÍN HIDRÁULICO DATOS TÉCNICOS MODELO H-1043 H-1193 H-1484 H-1366 H-1779 H-2640 H-1365 H-1780 H-1781 Capacidad (Lbs.) 5,500 3,300 Altura Máx. de Horquilla (Pulg.) Altura Mín. de Horquilla (Pulg.) Longitud de Horquilla (Pulg.) Ancho Total de Horquillas (Pulg.) Diámetro de la Llanta de Horquilla... -
Página 5: Mantenimiento
MANTENIMIENTO ACEITE o cuando se reemplazen los sellos. Para expulsar el aire, levante la palanca a la posición DOWN, y luego mueva Favor de revisar el nivel de aceite cada seis meses. la asa hacia arriba y abajo varias veces. La capacidad de aceite es aproximadamente 0.3L. -
Página 6: Solución De Problemas
NOTA: No intente reparar el patín hidráulico a menos de que haya sido entrenado o autorizado. π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 01-800-295-5510 uline.mx PAGE 6 OF 6 0312 IH-1043...