Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17

Enlaces rápidos

Series 6–EU Drills are designed for drilling operations in the aerospace, automotive,
appliance, electronic, machining and furniture industries.
Ingersoll–Rand is not responsible for customer modification of tools for applications on which
Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet
with 3/8" (10 mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 (6.2 bar/620 kPa)
psig maximum air pressure. Dust, corrosive fumes
and/or excessive moisture can ruin the motor of an
air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
SERIES 6–EU DRILLS
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool shaft may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
The Throttle Valve Cap is under pressure from the
Throttle Valve Spring. Use care when removing the
Throttle Valve Cap. (On tools where applicable.)
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
03533130
Form P6664–EU
Edition 8
October, 2000
GB
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 6–EU Serie

  • Página 17: Iinstrucciones Para Taladros De La Serie 6-Eu

    03533130 Impreso P6664–EU Edición 8 Octubre, 2000 IINSTRUCCIONES PARA TALADROS DE LA SERIE 6–EU NOTA Los taladros de la serie 6–EU están diseñados para las operaciones de taladrado de las industrias aeroespacial, del automóvil, electrodomésticos, electrónica, mecánica y del mueble. Ingersoll–Rand no aceptará...
  • Página 18: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro Usar siempre protección ocular Usar siempre protección de aire y desconectar la man- al manejar o realizar opera- para los oídos al manejar guera de suministro de aire ciones de mantenimiento en...
  • Página 19: Especificaciones

    PARA PONER LA HERRAMIENTA EN SERVICIO ESPECIFICACIONES GNivel de ruido ♦Nivel de Modelo Tipo de Velocidad en Capacidad de Empuñadura vacio portabrocas dB (A) vibraciones pulg. (mm) Presión Potencia 6LH1–EU palanca 6 000 1/4 (6) – – – – – – –...
  • Página 20: Declaración De Conformidad

    DECLARACIÓN DE CONFORMIDAD Ingersoll–Rand, Co. os abajo firmantes (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (domicilio) declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladros de las series 6–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE EN292 IS08662 PN8NTC1...
  • Página 25 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Company Ingersoll–Rand Nederland Produktieweg 10 510 Hester Drive 2382 PB Zoeterwoude White House Nederland TN 37188 Tel: (31) 71 452200 U.S.A. Fax: (31) 71 5218671 Tel: (615) 672 0321 Fax: (615) 672 0801 Ingersoll–Rand Company SA PO Box 3720...
  • Página 26 NOTES...
  • Página 27 NOTES...

Este manual también es adecuado para:

6lh1–eu6lj1–eu6ljj1–eu6lk1–eu6ll1–eu6lr3–eu

Tabla de contenido