Using The Remote Control - Jensen AQTIVE I Manual De Montaje Y Uso

1
UK
3
5
D
F
NL
ESP
N
ASSEMBLY / STARTING UP
First check whether all parts have been supplied. Refer to the
overview in the left foldout page of this brochure.
S
1. Lay the mattress upside down on the floor (see illus. 1).
2. Then lay the frame on top of the mattress (see illus. 1).
3. Fix the frame to the underside of the mattress using 4+4
FIN
screws (see illus. 2 en 3).
4. Fit the legs to the corner attachments on the lower frame
(see illus. 4).
5. Connect the electricity cable to the motor.
DK
6. Open the cover of the battery holder on the motor, remove the
plastic from the 9V batteries and connect these to the motor (illu. 5).
7. Turn the bed over.
8. Attach the side (illus. 6).
PL
9. Before fitting the two beds together, use the remote control to
move the head and foot ends to a horizontal position.
10.
Place the mattress topper on the bed (illus. 7).
11. Then insert the plug into the socket.
12. The motor and the remote control have been set at the factory.
The settings may be lost if there is a power cut for any
considerable length of time. Refer to the next paragraph for
information on how to adjust the settings of the remote control.
SETTING THE REMOTE CONTROL FOR ONE BED OR FOR
THE SIMULTANEOUS OPERATION OF TWO BEDS
1.
Press buttons 1 and 2 simultaneously until the lights start flas
hing quickly. The remote control is now in the setting mode.
2. Hold the remote control next to the motor of the bed that you
want to operate and press any button until the bed moves.
If you want to control two beds at the same time using a single
remote control, you should repeat the process for bed 2.
3. You can exit the setting mode by briefly pressing buttons 1 and
2, after which the lamps will go out. You can now operate the
bed(s).
4. If you want to revert to operating just one bed, repeat the above
steps.
MEMORY
1. Put the bed in the position you want to save.
2.
Press the M button until you notice the bed moving up and
down. Your preferred position will now have been saved to the
memory.
3. Pressing the M Button briefly will return the bed to the
horizontal position.
4.
Briefly pressing the M button again will return the bed to the
saved position.
4
JENSEN AQTIVE I
INTRODUCTION
Congratulations on the purchase of your Jensen Aqtive I adjustable bed. We hope this bed
2 gives you many years of comfortable days and nights. We recommend that you study this
manual closely before you start to assemble and install the bed.
4
GUARANTEE
6
If used normally, your Jensen Aqtive I is guaranteed for five years. The bill on which the
date of purchase is stated serves as a certificate of guarantee. In the event of any faults or
malfunctions, please contact the store from which you purchased the bed. When you do
so, please state the model number (see illustration 8).
7

USING THE REMOTE CONTROL

3The bed can be moved into different positions using the remote control.
Overview of the functions on the remote control:
1. Raise head end
2. Lower head end
3. Raise foot end
4. Lower foot end
MALFUNCTION
If you are unable to adjust the bed, proceed as follows.
•
•
•
•
•
NOISE LEVEL
A mechanical and electrically adjustable bed generates noise. The noise that
the bed makes may be reinforced by the acoustics of the room it is in.
EMERGENCY FUNCTION
In the event of a power failure, the bed can be moved to a horizontal posi-
tion by pressing button 2 (head end) and/or 4 (foot end) close to the bed
until it is again in an upright position. Replace the batteries in the motor
after this function has been used.
USAGE
The bed's lifting motors are not designed for continuous usage. The bed
will only continue to be reliable and operate for a normal life if the motors
do not operate for longer than 2 minutes during a 15 minute period. If this
limit is exceeded, the life of the products will be reduced and the guaran-
tee will no longer apply. The bed has been constructed in such a way that
it can bear a maximum weight of 150 kg, distributed equally over the entire
surface of the bed, from the head end to the foot end.
If you exceed these limits, the product will be damaged and the guarantee
one no longer apply. It is important that no-one is sitting on the head or
foot and of the bed while the bed is raised.
NB!
If used carelessly items may become trapped by the bed's moving
parts. You should therefore keep the remote control out of the reach
of children!
ELECTRICAL DATA
Power supply: 230 V AC 50/60 Hz.
Standby power: Max 0.5 W.
Reset the remote control, see point 12 under 'Assembly/starting up'.
Check whether the plug has been inserted properly into the socket and
that it is connected to the power supply.
Check that there are batteries in remote control. Replace the batteries if
they have run out.
If required remove the plug from the socket and repeat the procedure.
Do not open the motor, the electrical components or the remote control
yourself. The producer does not accept any liability if an unauthorised
person has opened the motor, or has tampered with the electrical
components or the remote control. New parts must be obtained from an
authorised supplier.
5. Raise head and foot end
simultaneously
6. Lower head and foot end
simultaneously
7. Memory