Using The Remote Control - Jensen AQTIVE II Manual De Montaje Y Uso

Ocultar thumbs Ver también para AQTIVE II:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 8
2
4
UK
6
8
D
F
NL
ESP
N
ASSEMBLY / STARTING UP
First, check whether all parts have been supplied. Refer to the overview in the left
foldout page of this brochure.
1. Place the bed on the side.
S
2. Cut the plastic strips on the chassis.
3. Fit the legs to the corner attachments on the lower frame (see illus. 1).
4. Fasten the footboard using the four bolts that are already attached to the foot
end of the bed (see illus. 2).
FIN
5. Install the attached 9V batteries in the motor (see illus. 3).
6. Connect power cable to the motor (see illus. 3). If you wish you can now
configure the bed. See paragraph on "Configuring a remote control to a bed".
7. Place bed on the legs.
DK
8. Attach the sidebar using two screws at a distance of approximately 80 cm
from the head end. Screw into the inside of the lower frame (see illus. 4).
9. In the case of double beds, no side bar should be fitted between the beds. Lay
the mattress and the mattress topper on the bed. Pull cover over the side bars
PL
and the foot board (see illus. 5).
10. Then insert the plug into the socket.
11. Refer to the next paragraph for information on how to adjust the settings of
the remote control to one bed or simultaneous operation of two beds.
ITA
SETTING THE REMOTE CONTROL FOR ONE BED OR FOR THE
SIMULTANEOUS OPERATION OF TWO BEDS
(Check that the bed is connected to power)
1. Press both buttons for "under bed light" at the same time until a red, flashing
light appear. The remote control is now in the setting mode.
2. Hold the remote control next to the motor of the bed that you want to operate
and press one of the buttons that raise the bed (4, 6 or 8) until the bed moves.
Both beds need to be in horizontal position before configuration. If you want to
control two beds at the same time using a single remote control, you should
repeat the process for bed 2.
3. You can exit the setting mode by pressing the buttons for "under bed light",
after which the lamps will go out. You can now operate the bed(s).
4. If you want to revert to operating just one bed, repeat the above steps.
ELECTRICAL DATA
Power supply: 230 V AC 50/60 Hz.
Standby power: Max 0.5 W.
MEMORY
1. Put the bed in the position you want to save.
2. Press the round button until you notice the bed moving up and down. Your
preferred position will now have been saved to the memory.
3. Pressing the round Button briefly will return the bed to the horizontal position.
4. Briefly pressing the round button again will return the bed to the saved
position.
LIGHT UNDER BED FUNCTION
Press the "light under bed" button and the light turns on to minimum strength.
Press and hold "light under bed" button for wanted light intensity. Press the "light
under bed" button again to turn the light off.
4
JENSEN AQTIVE II
INTRODUCTION
Congratulations on the purchase of your Jensen Aqtive II adjustable bed. We hope
1
3
this bed gives you many years of comfortable days and nights. We kindly request that
you study this manual closely before you start to assemble and install the bed.
5
GUARANTEE
7
If used normally, your Jensen Aqtive II is guaranteed for 5 years. The bill on which the
9
date of purchase is stated serves as a certificate of guarantee. In the event of any
faults or malfunctions, please contact the store from which you purchased the bed.
When you do so, please state the model number (see illustration 6).

USING THE REMOTE CONTROL

3The bed can be moved into different positions using the remote control.
Overview of the functions on the remote control:
1. Memory
2. Light under bed on
3. Light under bed off
4. Raise head end
5. Lower head end
THE BATTERIES IN THE REMOTE CONTROL IS DISCHARGED
The white background light vanishing on the buttons indicates low battery
function. Open the battery chamber, turn the remote control on its head, and
push the lever to the side simultaneously as the chamber is removed. Replace the
CR2450 3V battery and push the chamber back inside.
MALFUNCTION
If you are unable to adjust the bed, proceed as follows:
• Check whether the plug has been inserted properly into the socket and that it is
connected to the power supply. Check for the green light indicating power.
• Check that there are batteries in remote control. Replace the batteries if they
have run out.
• Check if the motor works with the App.
• If you have two beds, check if the remote control works the other bed.
• If required remove the plug from the socket, wait for 20 minutes and repeat the
procedure.
• Do not open the motor, the electrical components or the remote control yourself.
The producer does not accept any liability if an unauthorised person has opened
the motor, or has tampered with the electrical components or the remote
control. New parts must be obtained from an authorised supplier.
• Reset the remote control, see separate paragraph.
NOISE LEVEL
A mechanical and electrically adjustable bed generates noise. The noise that the
bed makes may be reinforced by the acoustics of the room it is in.
EMERGENCY FUNCTION (BATTERY BACKUP)
In the event of a power failure, check to see that the 9V batteries are installed. By
using the remote control, the bed can be moved to a horizontal position. Press the
button for lowering the head end until the bed is in a horizontal position. Replace
the batteries in the motor after this function has been used or once a year.
USAGE
The bed's lifting motors are not designed for continuous usage. The bed will only
continue to be reliable and operate for a normal life if the motors do not operate
for longer than 2 minutes during a 18 minute period. If this limit is exceeded, the
life of the products will be reduced and the guarantee will no longer apply. The
bed has been constructed in such a way that it can bear a maximum weight of
150 kg, distributed equally over the entire surface of the bed, from the head end
to the foot end. If you exceed these limits, the product will be damaged and the
guarantee one no longer apply. It is important that no-one is sitting on the head or
foot and of the bed while the bed is raised.
NB!
If used carelessly, items may become trapped by the bed's moving parts.
You should therefore keep the remote control out of the reach of children!
6.
Raise foot end
7.
Lower foot end
8.
Raise head and foot wend
simultaneously
9.
Lower head and foot end
simultaneously
Tabla de contenido
loading

Tabla de contenido