General Safety Rules - REMS Turbo K Instrucciones De Uso

deu
gereicht wird. Ersetzte Produkte und Teile gehen in das Eigentum von
REMS über.
Die Kosten für die Hin- und Rückfracht trägt der Verwender.
Die gesetzlichen Rechte des Verwenders, insbesondere seine
Mängelansprüche gegenüber dem Händler, bleiben unberührt. Diese
Hersteller-Garantie gilt nur für Neuprodukte, welche in der Europä-
ischen Union, in Norwegen oder in der Schweiz gekauft werden.
7. REMS Vertrags-Kundendienstwerkstätten
Firmeneigene Fachwerkstatt für Reparaturen:
SERVICE-CENTER
Neue Rommelshauser Straße 4
D-71332 Waiblingen
Telefon (0 7151) 5 68 08 - 60
Telefax (0 7151) 5 68 08 - 64
Wir holen Ihre Maschinen und Werkzeuge bei Ihnen ab!
Nutzen Sie in der Bundesrepublik Deutschland unseren Abholservice.
Einfach anrufen unter Telefon (0 7151) 5 68 08 - 60.
Oder wenden Sie sich an eine andere autorisierte REMS Vertrags-
Kundendienstwerkstatt in Ihrer Nähe.
Fig. 1–2
1 Tension spring
2 Fingertip switch in feed handle
3 Connection strap
4 Safety cover
5 Housing
6 Visor
7 Sawblade
8 Clamping lever
(only REMS Turbo K)
9 Scale (only REMS Turbo K)
10 Bearing block
(only REMS Turbo K)
11 Hexagonal bolt
(only REMS Turbo K)

General Safety Rules

WARNING! To reduce the risk of injury, user must read and understand
instruction manual.
WARNING! Read all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury. The term „power
tool" in all of the warnings listed below refers to your mains operated (cor-
ded) power tool or battery operated (cordless) power tool, also machines
and electric units. Only use the power tool for the purpose for which it was
intended, with the due attention to the general safety and accident preven-
tion regulations.
SAVE THESE INSTRUCTIONS.
A) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite acci-
dents.
b) Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
B) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock. If the power tool comes with an earthed wire, the plug may
only be connected to an earthed receptacle. At work sites, in damp sur-
roundings, in the open or in the case of comparable types of use, only
operate the power tool off the mains using a 30 mA fault current protected
switch (FI breaker).
b) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
C) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position
before plugging in. Carrying power tools with your finger on the switch
or plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool
eng
12 Length stop
(only REMS Turbo K)
14 Cooling lubricant container
(only REMS Turbo K)
15 Stand
16 Chucking lever
17 Cover disc
(REMS Turbo Cu-INOX)
18 Cooling lubricant pump
(REMS Turbo K)
19 Hole for cooling lubricant hose
20 Bolts for stand / cooling
lubricant container