Bosch GSR 36 V-LI Professional Manual Original página 16

OBJ_BUCH-487-002.book Page 16 Wednesday, April 6, 2011 8:11 AM
16 | English
Noise/Vibration Information
Measured sound values determined according to EN 60745.
GSR 36 V-LI
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Drilling into metal: Vibration emission value a
2
Uncertainty K =1.5 m/s ,
Screwdriving: Vibration emission value a
2
Uncertainty K=1.5 m/s .
GSB 36 V-LI
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Drilling into metal: Vibration emission value a
2
Uncertainty K =1.5 m/s ,
Impact drilling into concrete: Vibration emission value
2
a =11.5 m/s , Uncertainty K =1.5 m/s
h
Screwdriving without impact: Vibration emission value
2
a <2.5 m/s , Uncertainty K =1.5 m/s
h
GSR 36 V-LI/GSB 36 V-LI
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of ex-
posure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work
patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
1 619 929 J10 | (6.4.11)
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 25.03.2011
2
<2.5 m/s ,
Assembly
h
2
<2.5 m/s ,
Battery Charging
h
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
2
=3.0 m/s , does not damage the battery.
h
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
2
,
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
2
.
WARNING
tomatically switched off. The battery can be damaged.
Removing the Battery
The battery 8 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 14 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 8:
– Push the battery against the base of the power tool (1.) and
at the same time press the battery unlocking button 14 (2.).
– Pull the battery out of the power tool until a red stripe be-
comes visible (3.).
– Press the battery unlocking button 14 again and pull out
the battery completely.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indicator
12 indicate the charge condition of the battery 8. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Dr. Eckerhard Strötgen
Head of Product
Certification
Do not continue to press the On/Off
switch after the machine has been au-
Bosch Power Tools