Tabla de contenido
Idiomas disponibles
Idiomas disponibles
V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
ad just able. Re place belts if they begin to slip from wear.
TRANSAXLE MAINTENANCE
The transmission fan and cooling fi ns should be kept clean
to ensure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent pos-
si ble damage to seals, do not use high pressure water or
steam to clean transmission.
•
Inspect cooling fan to be sure fan blades are intact and
clean.
•
Inspect cooling fi ns for dirt, grass clippings and other
materials. To prevent damage to seals, do not use com-
pressed air or high pressure sprayer to clean cool ing fi ns.
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fl uid main te-
nance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
near est au tho rized ser vice center/department.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service
classifi cation SJ-SN. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE VISCOSITY GRADES
5W-30
-20
0
30
F
C
-20
-30
-10
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F/0°C. Check your
engine oil level more frequently to avoid possible engine
damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the tractor is not used for 25 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fi ll
cap/dipstick securely each time you check the oil level.
TO CHANGE ENGINE OIL (See Fig. 16 - 18)
Determine temperature range expected before oil change.
All oil must meet API service classifi cation SJ-SN.
•
Ensure tractor is on level surface.
•
Oil will drain more freely when warm.
•
Catch oil in a suitable container.
MAINTENANCE
SAE 30
32
40
60
80
0
10
20
30
Fig. 16
LOWER DASH COVER REMOVAL
•
Raise hood.
•
Remove fastener from lower dash cover.
CAUTION: Remove lower dash cover carefully to ensure
cover tabs are not broken.
•
Slide lower dash cover up to release cover tabs from
tapered slots in lower dash and remove.
LOWER DASH COVER
•
Remove oil fi ll cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
•
Remove yellow cap from end of drain valve and install
the drain tube onto the fi tting.
•
Unlock drain valve by pushing inward and turning
coun ter clock wise.
•
To open, pull out on the drain valve.
CLOSED
AND
LOCKED
POSITION
YEL LOW CAP
100
40
•
After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown.
•
Remove the drain tube and replace the cap onto to the
bottom fi tting of the drain valve.
•
Refi ll engine with oil through oil fi ll dipstick tube. Pour
slowly. Do not overfi ll. For approximate capacity see
"PRODUCT SPECIFICATIONS" section of this man u al.
•
Use gauge on oil fi ll cap/dipstick for checking oil level.
For accurate reading do not screw down dipstick cap.
Keep oil at the top of the crosshatched mark on dipstick.
Tighten cap onto the tube securely when fi nished.
16
TABS
Fig. 17
OIL DRAIN VALVE
DRAIN
TUBE
Fig. 18
SLOTS
Capítulos
Tabla de contenido
