Troubleshooting - Fellowes Metal 100r Manual De Instrucciones

Ocultar thumbs Ver también para Metal 100r:

Instrucciones del uso (16 páginas)

Tabla de contenido

Idiomas disponibles

ENGLISH

BINDING A DOCUMENT

MÁX 20

(80gsm)

Punch front and back covers

Punch sheets in small batches

ﬁrst.

so as not to overload the

machine or the user.

Hold the document in both hands,

Use the binding pliers to cut and

with the metal coil on the right

fold the end of the metal coil. Clip

side. Touch the metal coil against

off the excess coil.

the inserting roller to bind the

document.

CORRECTING A BOUND DOCUMENT

Additional sheets may be included or removed at any time by ﬁrst removing the old metal coil. Correct document as necessary, then rebind as

described.

REMOVAL OF WASTE CLIPPINGS

The waste tray is located in the back of the machine. For best results empty the tray regularly.

Metal100R_409587_RevB_3L_041317.indd 13-14

Switch the inserting roller on.

Collate the document. Load the

coil on to the ﬁrst 3 holes.

Turn the document around.

Clip off the excess coil.

TROUBLESHOOTING

Problem

Cause

Punched holes are not central

Edge guide not set

Machine will not punch

Blockage

Punch holes are not parallel to

Debris are stuck below dies.

edge.

Sheets not correctly aligned to punch

Partial holes

pattern.

Damaged hole edges

Possibly overloading the machine

WORLDWIDE WARRANTY

Fellowes warrants all parts of the binder to be free of defects in material

and workmanship for 2 years from the date of purchase by the original

consumer. If any part is found to be defective during warranty period,

your sole and exclusive remedy will be repair or replacement, at

Fellowes' option and expense, of the defective part. This warranty does

not apply in cases of abuse, mishandling or unauthorised repair. Any im-

plied warranty, including that of merchantability or ﬁtness for particular

purpose, is hereby limited in duration to the appropriate warranty period

W.E.E.E.

Español

Se clasiﬁca este producto como Equipamiento Eléctrico y Electrónico. Si llegase el momento de deshacerse de este producto, asegúrese que lo hace

cumpliendo la Directiva Europea sobre Residuos de Equipamiento Eléctrico y Electrónico (Waste of Electrical and Electronic Equipment, WEEE) y las leyes

locales relacionadas con esta directiva.

Para más información acerca de la Directiva WEEE, visite www.fellowesinternational.com/WEEE

Português

Este produto está classiﬁcado como Equipamento Eléctrico e Electrónico. Quando chegar a altura de eliminar este produto, certiﬁque-se de que o faz

em conformidade com a Directiva relativa a Resíduos de Equipamentos Eléctricos e Electrónicos (REEE) e em observância da legislação local relativa a

esta directiva.

Para obter mais informações sobre a Directiva relativa a Resíduos de Equipamentos Eléctricos e Electrónicos (REEE), visite o endereço www.

fellowesinternational.com/WEEE

English

This product is classiﬁed as Electrical and Electronic Equipment. Should the time come for you to dispose of this product please ensure that you do so in

accordance with the European Waste of Electrical and Electronic Equipment (WEEE) Directive and in compliance with local laws relating to this directive.

For more information on the WEEE Directive please visit www.fellowesinternational.com/WEEE

Solution

Adjust edge guide until hole pattern is correct

Check waste tray is empty. Check for blockage to paper

entry

Take stiff cardboard and slide into the paper entry. Move

the cardboard sideways to release any stray clippings into

the waste tray

Adjust edge guide and test punch scrap sheets until correct

Punch plastic covers with paper sheets. Reduce number of

sheets being punched

set forth above. In no event shall Fellowes be liable for any consequential