Traffic Light" Led Indicator (9); Maintenance And Service; Accessories; Storage - Narex ASV 200-2 BASIC Instrucciones De Uso Originales

English
Work mode selection (ASV 200-2 only)
Setting up torque
Turning the mode switch (6a) to the relevant symbol will set the
required torque�
Tightening
Symbol 1 = lowest tightening torque
18 = highest tightening torque
Symbol
Drilling
Symbol = maximum torque
Work mode selection (ASP 200-2 only)
You can set up tightening, impact free drilling or impact drilling by
turning the mode switch (6b) to the relevant symbol� You may also
use the torque set function for batch or gentle tightening when
setting up the drive mode� The machine has a maximum torque
available when setting the impact free drilling mode� Impact drill-
ing makes drilling more efficient, e�g� when drilling into brick or
other such hard construction materials�
Attention! Only change the tightening/drilling/impact drilling
modes while the machine is idle!
Always use only drill bits designed for impact drilling when drilling
in this manner�
Tightening
Symbol = suitable for tightening�
Impact free drilling
Symbol
= suitable for driving, drilling into metal, wood
etc�
Impact Drilling
Symbol = suitable for impact drilling into brick�
Setting up torque
The function for setting up torque can be used only if the machine
or set collar (6b) is set to tightening mode�
Proceed as per the above to set up torque�
Mounting and releasing tools
Turning the chuck mounting case (8) opens and closes the jaws
between which you place the working tools (drill bit, bit holder
etc�)� The machines are automatically equipped with a spindle stop,
which makes changing the tool using only one hand in the desired
direction very simple�
Mounting a belt clip
Place the machine onto a horizontal surface (e�g� a work table)�
Place the belt clip (12) onto the belt clip base (14) so that the
openings in the belt clip overlap with the threaded openings in the
machine� Secure the belt clip (12) using fastening screws (13) and
a corresponding screwdriver� You can mount the belt clip to the
machine from the right or the left side� Be careful not to mount the
belt clip the wrong way around� The belt clip position must match
the illustration�

"TRAFFIC LIGHT" LED indicator (9)

Battery charge status (capacity) indication:
Activates automatically once you press the switch button (3) and
switches off after approx� 3 seconds� The following LEDs light up
depending on the state of charge (capacity) of the accumulator:
• Accumulator is fully charged: all three status LEDs light up –
green, yellow and red�
• Accumulator capacity has dropped below ca� 60%: only two
status LEDs light up – yellow and red�
• Accumulator capacity has dropped below ca� 30%: only one
status LED lights up – red�
Indication of Reversible Defects
• Indication of low accumulator voltage – can occur when the
accumulator voltage reaches dangerously low levels that
could prevent repeated, proper and safe recharging� The con-
trol system will automatically disconnect the motor and a red
status LED will start flashing; release the switch and press it
again� If the problem persists, take the accumulator out of the
machine and place it in the charger to recharge it� Insert the
22
other (spare) accumulator into the machine and proceed with
your work�
• Overload indication – can occur as a result of excessive cur-
rent consumption, e�g� at an extremely high torque, in case
of a jammed tool etc� The control system will automatically
disconnect the motor and all three status LEDs will start flash-
ing – green, yellow and red� To restart the machine, release the
switch and then press it again�
• Overheat indicator – can occur in case of a long-term, extreme
load� The control system will automatically disconnect the mo-
tor and two status LEDs will start flashing – yellow and red� Let
the machine cool down before using it again� The cool down
time depends on how overheated the machine is�
Indication of Irreversible Defects
May occur as a result of a combination of factors� e�g� during a short
circuit, motor failure, accumulator failure etc� All three status LEDs
will start flashing – green, yellow and red� If the machine cannot be
restarted as per the above, bring it (along with the accumulator) to
your nearest authorised service centre�
Table overview of problems and signals:
Problem
Voltage too low
LED indicator Red flashing
Machine status Disconnected
Releasing and pressing the button (3)
Turning the
machine on
Inserting a
again
charged battery

Maintenance and service

Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device� Use protective goggles for this operation� Clean the
external plastic parts by a wet rag and mild detergent� Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent�
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start handling
the charger, disconnect the line plug from the socket!
Impurities and dust can be removed from external charg-
er surfaces by a rag or a non-metal brush� Use neither water nor
detergents�
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres"�

Accessories

The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el� tools�

Storage

Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C�
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes�

Environmental protection

Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy�
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
Reversible damage
Excess load Overheating
Green, yellow and Yellow and red
red flashing flashing
Disconnected Disconnected
Short-term break
to cool down
Irreversible
damage
Green,
yellow and red
flashing
Disconnected
Authorised
service centre