NuTone Heat-A-Lite 660RP Instrucciones De Instalación
  1. Manuales
  2. Marcas
  3. NuTone Manuales
  4. Calentadores
  5. Heat-A-Lite 660RP
  6. Instrucciones de instalación
NuTone Heat-A-Lite 660RP Instrucciones De Instalación

NuTone Heat-A-Lite 660RP Instrucciones De Instalación

Ocultar thumbs
1
2
3
4
5
6
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Heat-A-Lite
Combination
MODEL: 660RP
TYPE IC suitable for use under thermal insulation.
LOCATION
1. Mount heater to ceiling joists, or if necessary, to a header
installed between joists.
2. Caution: Do not mount heater closer than 12" to a
vertical surface. Do not mount over tub or in shower
enclosure.
3. Installation in existing construction required an
accessible area above the desired location. Make sure
that wiring can be run to the location.
MOUNTING HEATER HOUSING
NEW CONSTRUCTION
Using Hanger Bars
Refer to Figure 1.
1. Insert hanger bars in slots provided in housing.
2. Locate heater housing between joists so that bottom of heater housing is even with the planned finished ceiling.
3. Use screws or nails (not provided) to secure hanger bars to ceiling joists.
Using Side Mounting Tabs
1. Locate heater housing next to ceiling joist.
2. Use wood screws (not provided) through keyhole slots in mounting tabs to loosely attach housing to ceiling joist.
3. Adjust housing so that it will be flush with the finished ceiling. When housing is properly adjusted, tighten screw in slots to
secure housing.
EXISTING CONSTRUCTION
1. Determine desired location for heater.
2. Drill a small hole through the ceiling at the desired location and stick a coat hanger or stiff wire through hole into attic to
help find the location from above.
3. Check the area above to make sure that wiring can be installed and that the installation will not interfere with existing
electrical wiring.
4. From above, place the housing between ceiling joists at the desired location. Using the housing as a template, mark the
area to be cut out along the bottom flange of the housing.
5. After making the cutout, install the housing in the opening using the hanger bars or mounting tabs as described above.
Make sure that the bottom of the housing is flush with the bottom of the finished ceiling.
®
INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
FIGURE 1
loading

Manuales relacionados para NuTone Heat-A-Lite 660RP

Resumen de contenidos para NuTone Heat-A-Lite 660RP

  • Página 1 INSTALLATION INSTRUCTIONS READ & SAVE THESE INSTRUCTIONS! Heat-A-Lite ® Combination MODEL: 660RP TYPE IC suitable for use under thermal insulation. LOCATION 1. Mount heater to ceiling joists, or if necessary, to a header installed between joists. 2. Caution: Do not mount heater closer than 12" to a vertical surface.
  • Página 2 Connect green ground lead in the junction box to the WHITE supply ground. BLACK SUPPLY GROUND 4. Replace wiring compartment cover and tighten screw to SWITCH SHOWN IS NUTONE secure. ACCESSORY SWITCH HS-92 (SOLD SEPARATELY) 5. Insert plug from heater assembly into the white receptacle 120VAC LINE FIGURE 2 of the wiring compartment cover.
  • Página 3 INSTRUCCIONES DE INSTALACION ¡LEA Y GUARDE ESTAS INSTRUCCIONES! Combinación ® Heat-A-Lite MODELO: 660RP TIPO IC apto para usar debajo de aislamiento térmico. UBICACION 1. Monte el calentador en las viguetas del techo o, si es necesario, en un soporte instalado entre las viguetas. 2.

  • Página 4: Montaje Del Reflector Y De La Rejilla

    ALIMENTACION GROUND interruptor de calor. Conecte el hilo de tierra verde que EL INTERRUPTOR MOSTRADO ES EL SWITCH SHOWN IS NUTONE INTERRUPTOR ACCESORIO NUTONE HS-92 ACCESSORY SWITCH HS-92 está en la caja de uniones al suministro de tierra. (SOLD SEPARATELY)
  • Página 5 One Year Limited Warranty WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

  • Página 6: Parts List

    88570-000 89760 Grille 89760-000 53740 Lens 53740-000 89765 Reflector 89765-000 35758 Lamp Socket 35758-000 NuTone Attn: Parts Department 4820 Red Bank Road NOTE: Always order by Cincinnati, OH 45227-1599 current part number Phone: (513) 527-5426 Fax: (513) 527-5173 660RP I.I.