Tool Specifications - Bostitch SB-150SX Manual De Operación Y De Mantenimiento

All screws and nuts are metric.
MODEL TOOL ACTUATION
SB-1842BN
SB-1850BN
SB-150SX
SB-1664FN
SB-125BN
SB-2IN1
BTFP1850K
FASTENER SPECIFICATIONS:
TOOL MODEL BRAD SERIES
SB-125BN BT1300
SB-1842BN BT1300
SB-1850BN BT1300
SB-2 IN 1 BT1300
BTFP1850K BT1300
TOOL MODEL STAPLE SERIES CROWN WIDTH
SB-150SX SX5035
SB-2 IN 1 SX5035
TOOL MODEL NAIL SERIES
SB-1664FN SB16
TOOL AIR FITTING:
These tools use a free-flow connector plug, 1/4 N.P.T. The inside diameter should be
.200" (5mm) or larger. The fitting must be capable of discharging tool air pressure when
disconnected from the air supply.
OPERATING PRESSURE:
70 to 100 p.s.i.g. (4.9 to 7.0 kg/cm
best fastener performance.
DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
BOSTITCH OFFERS TWO TYPES OF OPERATION.
CONTACT TRIP
The common operating procedure on "Contact Trip" tools is for the operator to contact the work to actuate
the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted.
This will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly.
All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip,
and if unintentionally allowed to recontact the work surface with the trigger still actuated (finger still holding
trigger pulled) an unwanted second fastener will be driven.
SEQUENTIAL TRIP
The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This
makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications.
The Sequential Trip allows exact fastener location without the possibility of driving a second fastener
on recoil, as described under "Contact Trip". The Sequential Trip Tool has a positive safety advantage
because it will not accidentally drive a fastener if the tool is contacted against the work – or anything else
– while the operator is holding the trigger pulled.
MODEL IDENTIFICATION:
Refer to Operation Instructions on page 9 before proceeding to use this tool.
CONTACT
TRIP
Identified by:
BLACK
TRIGGER
LENGTH
Sequential Trip 9.25"
Sequential Trip 9.25"
Sequential Trip 9.50"
Sequential Trip 11.25"
Sequential Trip 9.25"
Sequential Trip 9.25"
Sequential Trip 9.25"
GAUGE
18
18
18
18
18
5-6mm
5-6mm
GAUGE
16
). Select the operating pressure within this range for
2
SEQUENTIAL
TRIP
Identified by:
GRAY
TRIGGER
-4-

TOOL SPECIFICATIONS

HEIGHT WIDTH
8.5" 2"
9.5" 2"
8.75" 2"
11.50" 3"
8" 2"
8.5" 2"
9.5" 2"
FASTENER RANGE
5/8" - 1-1/4"
5/8" - 1-5/8"
5/8" - 2"
5/8" - 1-5/8"
5/8" - 2"
FASTENER RANGE
1/2" - 1-1/2"
1/2" - 1-1/2"
FASTENER RANGE
1" - 2-1/2"
OPERATION
WEIGHT
2.38 lbs.
2.69 lbs.
2.65 lbs.
4.03 lbs.
2.12 lbs.
2.38 lbs.
2.69 lbs.