Identification Of Parts Identification Of Parts; Positioning The Unit; Operating The Unit; When Using The Unit - INVENTOR PR1-ION10L Manual Del Usuario

IDENTIFICATION OF PARTS
Dryer mode(optional)
The unit can make the MAX dehumidification function
when it is under the Dryer mode. The fan speed is fixed
at high fan speed. The humidity level is automatically
controlled according to the actual roomhumidity.The unit
will quit dryer mode after a maximum10 hours' operation.
NOTE
The Dryer mode must be operated in a closed room, do not
open any doors or windows.
To make the best effective dehumidification, please first
dehydrate the wet clothes.
Make sure to direct the airflow at the wet clothes (See Fig.A).
Thick and heavy wet clothes may not get the best
effective dehumidification.
CAUTION
Do not cover the air outlet of the unit with clothes. It may
cause excessive heat, fire or failure of the unit.
Do not place the wet clothes on the top of the unit and do
not allow make the water to drip into the. It may cause
electric shock, fire or failure of the unit.
Identification of parts
Front
Control panel
1
2 Handle
Air outlet grille
3
Water bucket
4
5 Water level window
Rear
1 Drain hose outlet
Caster
2
3
Power Cord and plug
4
Air intake grille
5
Air filter (behind the grill)
N O TE: All the pictures in the manual are
for explanation purposes only. The actual
shape of the unit you purchased may be
slightly different, but the operations and
functions are the same.
Wet clothes
30~50cm
30~50cm
Airflow
Allow 30~50cm of distance
on the top and right side of
the unit away from the
wet clothes.
Fig.A
1
2
3
4
5
Fig.2
1
2
3 Fig.3

Positioning the unit

Adehumidifier operating in a basement will have little or no effect in drying an adjacent enclosed
storage area, such as a closet, unless there is adequate circulation of air in and out of the area.
Do not use outdoors.
This dehumidifer is intended for indoor residential
applications only. This dehumidifier should not be used
for commercial or industrial applications.
Place the dehumidifier on a smooth, level floor strong
enough to support the unit with a full bucket of water.
Allow at least 20cmof air space on all sides of the unit
for good air circulation.
Place the unit in an area where the temperature will not
fall below 5ºC(41ºF). The coils can become covered with
frost at temperatures below 5ºC(41ºF), which may reduce
performance.
Place the unit away fromthe clothes dryer, heater or radiator.
Use the unit anywhere books or valuables are stored to
prevent moisture damage.
Use the dehumidifier in a basement to help prevent
moisture damage.
The dehumidifier must be operated in an enclosed
area to be most effective.
Close all doors, windows and other outside openings
to the room.

When using the unit

When first using the dehumidifier, operate the unit
continuously for 24 hours.
This unit is designed to operate with a working
environment between 5ºC/41ºF and 35ºC/95ºF.
If the unit has been switched off and needs to be
switched on again quickly, allowapproximately
three minutes for the correct operation to resume.
Do not connect the dehumidifier to a multiple socket
outlet, which is also being used for other electrical
appliances.
Select a suitable location, making sure you have easy
access to an electrical outlet.
Plug the unit intoa electrical socket-outlet with earth
connection.
Make sure the water bucket is correctly fitted otherwise
the unit will not operate properly.
NOTE: When the water in the bucket reaches to a certain
level, please be careful moving the unit to avoid it from
falling down

OPERATING THE UNIT

40cm or
more
Air outlet grille
Air intake
grille
20cm or more
20cm or more
20cm or more
20cm or more
Fig.4a
Casters(At four points on the bottomof unit)
Casters can move freely.
Do not force casters to move over carpet,
nor move the unit with water in the bucket.
(The unit may tip over and spill water.)