LEGRAND Wattstopper LMCP8-10V Instrucciones De Instalación

No: 24788 – 05/21 rev. 4
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: LMCP8-10V/LMCP24-10V/LMCP48-10V
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
WARNING
IMPROPER INSTALLATION OR
CONNECTION OF THIS PANEL MAY
RESULT IN SERIOUS PERSONAL
INJURY AND/OR DAMAGE TO THE
PANEL AND OTHER DEVICES.
Wattstopper
DLM Relay Panel Interiors with 0-10V Dimming or Switched On/Off
Intérieurs du panneau a relais DLM avec gradation 0-10 V ou On/Off
Interiores del panel de relés DLM con atenuación de 0-10 V o
encendido/apagado
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
LMCP8/LMCP24/LMCP48
SPECIFICATIONS
Input voltage ................. 115/277V, 120/347V, 240V Single Phase, 50/60 Hz
For 0-10V models:
Sinks up to 100 mA per 0-10V input (50 fixtures at 2mA each)
0-10V signal will open on loss of power to panel
Class 2 connection to two independent DLM local networks
24VDC output ...............up to 250mA across 2 RJ45 ports per local network
..................................................................(A and B networks, 250 mA each)
Free-topology DLM local network may include Digital Lighting Management
(DLM) switches, occupancy sensors, daylight sensors, load controllers, and
input modules.
Category 5e cable, 150 feet per device, up to 1,000 ft. total per local network
Terminals for connection to DLM segment network (BACnet MS/TP)
Segment network parameters
Wattstopper LM-MSTP wire
Linear topology, 4000 ft. maximum per segment
Accessory power (jumper selectable)
LMCP8/LMCP8-10V ............................................................................N/A
LMCP24/LMCP24-10V ................ 650 mA @ 15VDC, 400 mA @ 24VDC
LMCP48/LMCP48-10V ................ 650 mA @ 15VDC, 400 mA @ 24VDC
...............................15VDC to power optional internal Network Controller
...................................................... 24VDC for Class 2 accessory devices
HDR relays (used in both On/Off and 0–10V panels):
Coil voltage, 24VDC, pulse ON and pulse OFF
Mechanically latched contacts
½" K.O. mounting, LV plug-connection, individually replaceable
HDR Heavy Duty Relay contact ratings:
30 A ballast .................................................................................. @ 277V
20 A ballast .................................................................................. @ 347V
16 A, E-Ballast ............................................................................. @ 120V
10 A, E-Ballast ............................................................................. @ 277V
20 A tungsten ............................................................................... @ 120V
30 A resistive ............................................................................... @ 347V
20 A receptacle load .................................................................... @ 120V
1.5 HP .......................................................................................... @ 120V
SCCR (short circuit current rating) ..........................14,000 A @ 347VAC
Operating conditions:
for indoor use only ................................................... 32–140° F (0–60° C)
...................................................................... 5-95% RH, non-condensing
UL and cUL listed (E207852). Listed for receptacle rated circuit control
Complementary Listed to Emergency Lighting Equipment, UL924
OSHPD (OSP) Approved (Certification No: OSP-0257)
WARNING: The DB9 cables cannot be plugged in or unplugged
without powering down the panel.
®