HELDEN VANITY INSTALLATION
The following installation instructions apply to the Helden vanity specifically. They are applicable for both the 36" and 60" wide versions
of the vanity.
2. Wooden support
(2 pcs)
PARTS
3. Stainless steel screw Ø6x40
(9 pcs)
(2) Steel Bracket
4. Stainless steel screw Ø4x25
(9 pcs)
PREPARE THE VANITY
BEFORE STARTING: Remove any drawers and set aside in a secure location (see page 5 for instructions).
1. Measure and mark plumbing stub out locations on the back of the vanity.
2. DRILLING FROM THE INSIDE OF THE VANITY TOWARD THE BACK, use a hole saw to cut out the marked locations.
Steel screw
5.
1
(6 pcs)
4x38mm
Ø
Jonathan Sowterathan Charles
- Fine Furniture
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376
www.robern.com
(1) Wall Cleat
Quantities shown are for 36" wide vanity. 60" wide vanity ships with fewer components.
@ Copyright 2004 all right reserved by
4x38mm
Ø
Jonathan Sowterathan Charles
(2 sets)
3. Stainless steel screw Ø6x40
ASSEMBLY INSTRUCTIONS
(9 pcs)
1. Preset the cabinet on your desired
2. Wooden support
location,and mark the location with a light
(1 pcs)
pencil mark. Use tape or pencil to
4. Stainless steel screw Ø4x25
transcribe the location of the back of the
(9 pcs)
cabinet pre-installed bracket to the wall.
3. Stainless steel screw Ø6x40
Below this making is where you will install
(6 pcs)
the included metal wall- mount bracket. See
FIGURE 2.
2. Hold the bracket against the wall and mark
Steel screw
5.
4. Stainless steel screw Ø4x25
with pencil the locations of the bracket srew
(6 pcs)
(6 pcs)
holes,ensuring levelness. See FIGURE 2.
3. Drill a hole on each mark and then tap
[203-1564]
(6) 1/4" x 1-9/16" Screw
anchor into hole until flush with surface.See
"ASSEMBLY INSTRUCTIONS BY WALL
Steel screw
Ø
4x38mm
5.
@ Copyright 2004 all right reserved by
(3 pcs)
TYPE" for mounting instructions base on
your wall type: concrete,drywall, or drywall
and studs.
4. Tighten the screws into the anchors while
Jonathan Sowterathan Charles
maintaining constant pressure on the
anchor to set.Remove screw. Hold metal
bracket over the inserted anchors, and
reinstall screws through the wall bracket
holes, and lighten until snug against wall.
See FIGURE 1.
2
5. Install the cabinet on the wall bracket as
illsustrated in FIGURE 3.
- Fine Furniture
7
cabinet pre-installed
Below this making is
the included metal wa
FIGURE 2.
2. Hold the bracket again
with pencil the locatio
holes,ensuring leveln
3. Drill a hole on each ma
[216-1239] Mounting
Hardware Bag
anchor into hole until
"ASSEMBLY INSTRU
TYPE" for mounting i
Ø
4x38mm
your wall type: concre
and studs.
[203-1565]
(6) #8 x 1" Screw
4. Tighten the screws into
maintaining constant
Jonathan Sowterathan Charles
- Fine Furniture
anchor to set.Remov
bracket over the inse
reinstall screws throu
- Fine Furniture
holes, and lighten unt
See FIGURE 1.
5. Install the cabinet on th
illsustrated in FIGURE
location,and mark the locatio
pencil mark. Use tape or pen
transcribe the location of the
cabinet pre-installed bracket
Below this making is where
the included metal wall- mou
FIGURE 2.
2. Hold the bracket against the w
with pencil the locations of t
holes,ensuring levelness. Se
3. Drill a hole on each mark and
anchor into hole until flush w
"ASSEMBLY INSTRUCTION
TYPE" for mounting instruct
your wall type: concrete,dryw
and studs.
4. Tighten the screws into the an
maintaining constant pressu
anchor to set.Remove screw
bracket over the inserted an
reinstall screws through the
holes, and lighten until snug
[203-1566]
See FIGURE 1.
(3) #8 x 1-1/2" Screw
5. Install the cabinet on the wall
illsustrated in FIGURE 3.
Part no. 209-1416 07/21/2021
Craft Series & Curated Bath Vanity
4. T
5. In