Tabla de contenido
Idiomas disponibles
Idiomas disponibles
* Models with cappuccino maker:
2. With one hand, hold the cappuccino maker spout firmly,
with the other, release the cappuccino maker by turning it
anticlockwise, then pull off downwards (fig. 27).
3. Remove the steam connection nozzle from the spout by
pulling it downwards.
4. Wash the cappuccino maker and steam connection nozzle
thoroughly with warm water.
5. Make sure the two holes shown by the arrows in fig. 28 are
not blocked. If necessary, clean with a pin.
*All models:
6. Put the steam connection nozzle back, pressing forcefully
upwards to insert it onto the steam tube.
7. Replace the cappuccino maker by pushing upwards and
turning clockwise.
12. HOT WATER
1. Press the ON/OFF switch (fig. 12) to turn the appliance on.
The power light comes on.
1. Wait until the
light comes on.
2. Place a recipient under the cappuccino maker.
3. When the
light comes on, press the
(fig. 15) and at the same time turn the steam dial to
ON (fig. 24). Water comes out of the cappuccino maker.
4. To interrupt hot water delivery, press the
again and turn the steam dial to OFF.
You should not deliver hot water for more
than 60 seconds.
13. CLEANING
Danger!
•
While cleaning, never immerse the coffee maker in water.
It is an electrical appliance.
•
Before cleaning the outside of the appliance, turn it off,
unplug from the mains socket and allow to cool.
13.1 Espresso coffee filter cleaning and
maintenance
About every 300 coffees or when the coffee is delivered from the
filter holder a drop at a time or not at all, clean the pre-ground
coffee filters and filter holder as follows:
•
Remove the filter from the filter holder.
•
Remove the filter cap (fig. 29) by unscrewing in the direc-
tion indicated by the arrow on the cap.
•
Remove the frother from the container by pushing it from
the cap end (fig. 30).
•
Remove the gasket (fig. 30).
•
Rinse all components and clean the metal filter thoroughly
in hot water using a brush (fig. 31). Make sure the holes in
the metal filter are not blocked. If necessary, clean with a
pin (see fig. 31).
•
Replace the filter and gasket on the plastic disk as shown in
fig. 32. Make sure to insert the pin on the plastic disk into
the hole in the gasket indicated by the arrow in fig. 32.
•
Replace the assembly in the steel filter container (fig. 33),
making sure the pin is inserted in the hole in the support
(see arrow in fig. 33).
•
Finally, screw on the cap.
Failure to clean as described above invalidates the guarantee.
button
13.2 Cleaning the boiler outlet
About every 300 coffees, the espresso boiler outlet must be
button
cleaned as follows:
•
Make sure the appliance is not hot and that it is unplugged
from the mains;
•
Use a screwdriver to release the screw fixing the espresso
boiler outlet (fig. 34);
•
Remove the boiler outlet;
•
Clean the boiler with a damp cloth (fig. 34);
•
Clean the outlet thoroughly with hot water using a brush.
Make sure the holes are not blocked. If necessary, clean
with a pin (fig. 31).
•
Rinse under running water, brushing all the time.
•
Replace the boiler outlet, making sure it is correctly posi-
tioned on its gasket.
Failure to clean as described above invalidates the guarantee.
13.3 Other cleaning operations
1. Do not use solvents or abrasive detergents to clean the cof-
fee maker. Use a soft damp cloth only.
2. Clean the filter holder, filters, drip tray and water tank reg-
ularly.
To empty the drip tray, extract the cup tray grille, remove
the water and clean the tray with a cloth: then reassemble
the drip tray.
11
33
34
Tabla de contenido
Solución de problemas
