Worx WG255 Manual Del Usuario página 10

oPErATING INsTrUCTIoNs
warNiNg! do not use the product
without attaching the guard and
front handle.
1. guard aSSEmBly
Insert the guard into the slot as illustrated in
Fig.A; making sure it is securely attached.
Use two screws to fix the guard securely.
2. FroNT haNdlE aSSEmBly
The front handle must be assembled before use:
1) Attach the handle to the housing, aligning
the mark to housing and handle (See Fig.
B, C, D).
2) Insert the locking bolt into the handle and
fully tighten the bolt. (See Fig. e)
3) Check whether handle is firmly secured, if
not retighten the locking bolt.
3. BEForE uSiNg your CordlESS
hEdgE TrimmEr
warNiNg! The charger and battery pack
are specially designed to work together
so do not attempt to use any other devices.
10 10
Never insert or allow metallic objects into your
charger or battery pack connections because of
an electrical failure and hazard will occur.
Your battery pack is UNChARGeD and you
must charge once before use.
The battery charger supplied is matched to the
Li-ion battery installed in the machine. Do not
use another battery charger.
4. ChargiNg your BaTTEry PaCk
The Li-ion battery is protected against deep
discharging. When the battery is empty,
the machine is switched off by means of a
protective circuit: The tool holder no longer
rotates.
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool
down before recharging.
5. To rEmovE or iNSTall BaTTEry
PaCk (See Fig. F)
Depress the battery release button (7) to
release battery pack from your hedge trimmer.
Cordless li-ion hedge trimmer
All manuals and user guides at all-guides.com
After recharging, insert the battery pack into
trimmer's battery port. A simple push and
slight pressure will be sufficient. Check to see
if the battery is fully secured.
6. STarTiNg aNd SToPPiNg
BEForE STarTiNg your hEdgE
TrimmEr
Remove blade sheath (9).
To STarT your hEdgE TrimmEr
Your hedge trimmer is equipped with two
switch levers (5 & 6). Both switch levers need
to be pressed for the hedge trimmer to start.
Depress and hold the front switch lever (5) and
press the rear switch lever (6) (See Fig. G).
To SToP your hEdgE TrimmEr
Move hedge trimmer away from cutting area
before stopping.
To stop, release one of the switch levers (See
Fig. h).
warNiNg: if any parts are missing,
damaged or broken, do not operate
your hedge trimmer until all damaged
parts have been replaced or repaired.
Failure to do so could result in serious
personal injury. do NoT uSE wiThouT
haNdlE aNd guard
7. how To uSE your hEdgE TrimmEr
Note that the switch lever can be activated
on three sides, giving you many choices for
a comfortable grip. Before cutting an area,
inspect it first and remove any foreign objects
that could become thrown or entangled in
the blades. Always hold the trimmer with
both hands and with the blade away from you
before turning it on.
When trimming new growth, use a wide
sweeping action so that the stems are fed
directly into the blade. (See Fig. I& J)
Allow the cutting blades to reach full speed
before cutting. When operating, keep the
cutting blades away from people and objects
such as walls, large stones, trees, vehicles, etc.
If the blade stalls, immediately stop the
trimmer. Release the two switch levels (5 &
6) before attempting to clear jammed debris
from the cutting blades.
Wear gloves when trimming thorny or prickly
growth.
EN