Before Welding - GYS GYSMATIC TRUECOLOR GOGGLE 3 Manual De Usuario

Translation of the original instructions
The opto-electronic filter in the mask is not waterproof and
will not function properly if it has been in contact with water.
The welding mask must be moved carefully to avoid damage
to the filter, guards and/or protective shell.
Maintenance :
- Do not place heavy objects or tools on or in the facepiece
to avoid damage to the filter or face shields.
Mask storage temperatures range from -10°C to +60°C.
- Clean the Optoelectronic Filter with a clean cotton or
special lens cloth.
- Regularly clean and change the guard screens.
- Clean the inside and outside of the mask with a neutral
detergent-disinfectant. Do not use solvents.
- Make sure that the sensors and cell are not obstructed by
dust or debris.
- We recommend using the mask and visors for 5 years.
The length of use depends on various factors such as type
of use, cleaning, storage and maintenance.

BEFORE WELDING

-Check that the welding helmet is in good condition and headband adjustment.
-Check whether the front cover lens, the front frame and filter are inserted and fixed in place. In case of anomalie, please proceed to its reconditionning.
-Make sure that the sensors and the cell are not obstructed by dust or debris.
-Make sure that the protection films on both screens are removed.
-Check that the protection level matches your welding processes. Please refer to the following chart to help your choice (cf. welding process board)
OPERATION
The opto-electronic GYSMATIC LCD GOGGLE 3 welding helmet instantaneously switches from light to dark state when a welding arc is struck and switches back to the light
state when the arc stops.
1
2
9
● Switch button «WELD / GRIND / CUT» :
The « WELD / GRIND / CUT » switch botton is used to adjust the shade according to the selected adjustment range (4-8 or 8-13).
WELD : shade 8-13
MODE
CUT : shade 4-8
1
GRIND : shade 3 (off)
For non-welding operations such as grinding, it is possible to disconnect the sensor by switching the potentiometer to the «GRIND» mode.
CAUTION: Make sure to switch back to «WELD» mode before any welding operation.
• «Sensitivity» buttons : Setting of the sensitivity :
- «-» : Short Press-Decrease the sensitivity. Long Press- Anti-light interference mode on/off. When Anti-light interference is on, the sensitivity
area displays a bulb icon.
SENS
2
- «+» : Short Press -Increase the sensitivity. Long Press - In the cut or weld mode, set sensitivity automatically.
When automatic sensitivity function is enabled, SENS area will be shown «AUTO». The sensitivity numbers will increase from 0 to 8 in turn, and
stop at the gear number which is automatically set. Then the system will quit the automatic sensitivity setting mode.
• «Delay» buttons : Time to get the clear state back.
Delay is designed for slower switching time to clear state to eliminate remained bright rays.
- «-» : Short Press : Decrease the delay time. Long Press : Enter or exit automatic delay time function. When automatic delay time function is
DELAY
3
enabled, the screen of DELAY area will show «AUTO». The gear numbers on the screen can adjust from -9 to +9.
- «+» : Short Press : Increase the delay time. Long Press-Enter or exit gradual return function. In the weld mode, When gradual return function
is enabled, the screen of DELAY area will show «G».
GYSMATIC TRUECOLOR GOGGLE 3
3
4
5
8
7
6
10
8
EN
1. Switch mode button «GRIND-WELD-CUT»
2. «Automatic/Manual» switch shade button
3. Decrease shade button
4. Increase shade button
5. Decrease sensitivity button
6. Increase sensitivity button
7. Decrease delay button
8. Increase delay button
9. Setting the left window
10. Setting the right window