Stanley SL2M09 Manual De Instruccion página 4

Spotlight Bulb Replacement (Diagram Follows)
To replace the bulb, you will need a small Phillips screwdriver and a 6 volt/75 watt replacement bulb. During installation, avoid
touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be
wiped clean with a cloth moistened with alcohol.
RUBBER BEZEL
GLASS
Use a screwdriver to gently
LENS
pry the Rubber Bezel off.
RETAINING
RING
HALOGEN BULB ASSEMBLY
HAIRPIN
RETAINING
WIRE
LIGHT REFLECTOR
1. Disconnect the unit from any charging adapters.
2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in the retaining ring.
3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.
4. Lift off the retaining ring, glass lens and rubber "O" ring and set them aside.
5. Carefully remove the reflector and bulb assembly.
6. Disconnect the bulb wire from the red power wire.
7. Unsnap the hairpin retaining wires from the reflector' s flange.
8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely remove this
screw).
9. Lift out the bulb and detach wire.
10. Insert the replacement bulb into the reflector' s flange.
11. Put back and secure the hairpin retaining wires.
12. Connect the bulb power wire to the red power wire.
13. Tighten the retaining screw on the flange.
14. Place the reflector in position in the body of the spotlight.
15. Replace the rubber "O" ring in the groove around the perimeter of the reflector.
16. Replace glass and retaining ring so the screw holes are aligned.
17. Secure retaining ring with two screws.
18. Replace rubber bezel.
19. Operate switch to ensure proper operation of spotlight.
WARNING: To reduce the risk of electric shock, replace bulb with 12 volt, H3 100 watt only.
12 volt DC charger plug fuse replacement
The fuse in the plug end of the 12 volt DC charger protects the adapter' s charging circuit. If the 120 volt AC charger operates, but the DC
charging adapter does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
SL2M09_ManualENSP_080315.indd 6-7
LIGHT PHILLIPS SCREW
REFLECTOR
PHILLIPS ON/OFF
TRIGGER
SCREW
RUBBER
"O" RING
HALOGEN BULB
ASSEMBLY
Only replace the bulb in an
integrated assembly of lamp
holder, wire and tab.
RETAINING
SCREW
6
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 2 amp/250 volt fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 Volt DC Charging Adapter.
TROUBLESHOOTING
The charging status indicator LED does not flash when charging
1. Check connection to the 120 volt AC charger or 12 volt DC charger.
2. Check connection to AC or DC power source.
3. Confirm there is a functioning AC or DC current.
Unit will not operate
1. The halogen bulb may have blown. Check bulb filament. If the filament is coiled and unbroken, the bulb is not blown.
Otherwise, replace the bulb following the instructions in this manual.
2. The battery may be completely discharged. Charge the unit following the directions in this manual.
3. If the spotlight does not operate after recharging as directed, contact manufacturer at (877) 571-2391.
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you need assistance regarding
accessories, please contact the manufacturer at (877) 571-2391.
WARNING: The use of any accessory not recommended for use with this appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at (877) 571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from the date
of retail purchase by the original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the
following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturer' s option. Proof of purchase
may be required by manufacturer. (2) Return the product to the retailer where product was purchased for an exchange (provided
that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer' s return policy
for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs fuses and batteries, defects resulting from normal wear and tear, accidents,
damages sustained during shipping, alterations, unauthorized use or repair, neglect, misuse, abuse, and failure to follow
instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to
state or province to province. This product is not intended for commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the product to: Baccus Global LLC, One
City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432. Baccus Global LLC, toll-free number: 1-877-571-2391.
SPECIFICATIONS
Spotlight bulb: 6 volt, 75 watt
Battery: Maintenance-free, sealed lead acid, 6 volt, 4.5 amp hour
AC input: 120VAC, 60Hz, 7W
DC input: 12VDC
Imported by Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
RD080315
7
8/3/2015 1:54:13 PM