Manual Tune; Factory Reset; Technical Specification - Denver DAB-35 Manual Del Usuario

DENVER DAB-35
DAB Auto Scan
The auto scan will search for the entire DAB Band III channels, After the scan has finished, the first
alphanumerically found stations will be automatically selected.
To activate auto scan, press and hold MENU button, and press ▼/▲ buttons to enter into the
1.
Menu to select "Full scan", finally press the SELECT button to confirm. The display will show
"Scanning..." and a pressing slide bar.(F.3)
2. All the stations that have been found will be stored automatically, press ▼/▲ buttons to
explore the stations that have been found. When you find a station that you would like to listen,
press the SELECT button to confirm.
DAB Manual tune
1. To select manual tune, press and hold MENU/INFO button, and then press ▼/▲ buttons to
select "Manual tune"(F.4). And press the SELECT button to confirm.
2. Press ▼/▲ buttons to move through the DAB channels, the display will show "5A to 13F" and
their associated frequencies. (F.5)
3. When your desired frequency appears in the display, press the SELECT button to listen, the
name of the station group (ensemble/multiplex) will be displayed.
F.3 F.4
DAB
< Full scan > < Manual tune >
FM radio
1. To select FM, press the MODE button, the display will show FM and the frequency.
To activate auto search, press SELECT button or press and hold ▼/▲ buttons until the radio
2.
starts to scan the frequency band, the display will show 'Scanning ...'(F6), and it will stop
automatically once a station has been found.
3. To search manually, press ▼/▲ buttons in the desired direction to increment the frequency by
0.05MHz. If reception is still poor adjust the position of the antenna or try moving the radio to
another location.
F.6
92.75MHz
Scanning . . .
Scan setting
In FM mode, press and hold MENU/INFO button and then press ▼/▲ buttons to select
"Scan setting". And press the SELECT button to confirm. Press ▼/▲ buttons to select
"All stations/Strong stations only", and then press the SELECT button to confirm the setting.
USING HEADPHONES (not included)
A stereo headphone jack has been provided so that the radio can be used without disturbing others.
Plug in the headphones at the point marked '
level. Excessive sound pressure from earphones and headphones can cause hearing loss. The
speakers will not operate when earphones are fitted.
F.5
DAB

Manual tune

< 5A 174.928MHz >
' and adjust the listening volume to your chosen
ENG-3
DENVER DAB-35
RESET
1. If moving the radio to another location in the country the pre-tuned and stored DAB stations
may no longer be available and it will be necessary to reset the radio back to the factory settings.
2. With the unit switched on, press and hold the MENU/INFO button and press ▼/▲ buttons
until the display shows 'System' and press the SELECT button and continue press ▼/▲ buttons
until the display shows "Factory Reset <No> Yes' and press ▼/▲ buttons to "<Yes>" and press
the SELECT button. (F.7), (F.8)
3. The radio will display "Restarting...." and will then go into standby mode.
Note 1: All stored programmed stations will be lost during reset.
Note 2: Use the battery status without reset function.
F.7
System
< Factory Reset >

TECHNICAL SPECIFICATION

Rated voltage (adaptor) AC 100 – 240V~ 50/60Hz, 0.2A
Adaptor output DC 6V
Rated voltage (radio) DC 6V (1.5V x 4 AA)
Power consumption 6 W
Audio output 2 W RMS
Radio DAB 174-240MHz
FM 87.5-108MHz
Operating conditions Temperature: 5°C to 35°C
Humidity 5% to 90%
Unit dimension : 190 (L) × 110(W) × 115 (H) mm
Weight : 0.8kg
***SPECIFICATION SUBJECT TO CHANGE WITHOUT FURTHER NOTICE.***
F.8

Factory Reset ?

< No > Yes
1A
ENG-4