Basic Operation - Tripp-Lite OMNI1300LCD Manual Del Propietário

Ocultar thumbs

página de 6

/ 6
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

Basic Operation

(Front Panel)

3c) "AVR" (Automatic Voltage Regulation) Icon: This icon will illuminate whenever the

UPS is automatically correcting low AC line voltage without depleting battery power. This

is a normal, automatic operation of the UPS, and no action is required.

3d) "REPLACE" (Battery Recharge/Replace) Icon: This icon will illuminate and an

alarm will sound after a self-test to indicate the UPS battery needs to be recharged or

replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the

icon continues to illuminate, contact Tripp Lite for service. Battery replacement should only

be performed by qualified service personnel. If the UPS requires battery replacement, Tripp

Lite offers a complete line of replacement batteries at www.tripplite.com.

3e) "ON BAT" (On Battery) Icon: During a severe brownout or blackout, this icon

illuminates and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS is

operating from its internal batteries. Monitor the "Battery Capacity" Meter to determine the

Basic Operation

(Rear Panel)

AC Outlets

AC Outlets: All outlets provide connected equipment with AC line power (backed by surge

protection and line noise filtering) during normal operation. Automatic voltage regulation

continually corrects brownout (low voltage) and high voltage conditions without using battery

power. All outlets provide battery power during blackouts and severe brownout or severe high

voltage conditions.

USB and RS-232 Communication Ports: These ports can connect the UPS to audio/video

control systems, media center PCs or music servers for automatic file saves and unattended

shutdown in the event of a power failure. Use with Tripp Lite's PowerAlert Software (available

as a FREE download at www.tripplite.com) and appropriate USB or DB9 cable. Note: This

connection is optional. The UPS will work properly without this connection. Also Note: This

UPS System provides basic communication compatibility with most integrated Windows

Macintosh

and Linux

power management applications.

Tel/DSL/Network Line Surge Protection Jacks: The UPS has jacks that protect against

surges on a single phone, fax, modem or Ethernet network line. Using appropriate telephone or

network cords, connect the wall jack to the UPS jack marked "IN." Connect the equipment to

the UPS jack marked "OUT." Make sure the equipment connected to the jacks is also protected

against surges on the AC line. Connecting equipment to these jacks is optional. The UPS will

work properly without this connection. Not compatible with PoE (Power Over Ethernet)

applications.

Coaxial Protection Jacks: Gold coaxial connectors protect components by stopping surges on

DSS satellite, cable or antenna lines. Connect a coaxial cable from the wall jack directly to the

coaxial jack labeled "IN." Connect a coaxial cable from the coaxial jack labeled "OUT"

directly to the device to be protected. The UPS system must always be the first item connected

Storage

To avoid battery drain, all connected equipment should be turned off and disconnected from the

UPS. Press and hold the ON/OFF button for one second. The UPS will be completely turned off

(deactivated), and will be ready for storage. If the UPS will be stored for an extended period, fully

recharge the UPS batteries every three months. Plug the UPS into a live AC outlet, turn it on by

pressing and holding the ON/OFF button for one second, and allow the batteries to recharge for 4

to 6 hours. If the UPS batteries are discharged for a long period of time, they will suffer a

permanent loss of capacity.

Service

Before returning the UPS for service, follow these steps: 1. Review the installation and operation

instructions in this manual to ensure that the service problem does not originate from a misreading

of the instructions. 2. If the problem continues, do not contact or return the UPS to the dealer.

Instead, call Tripp Lite at (773) 869-1233. A service technician will ask for the UPS's model

number, serial number and purchase date and will attempt to correct the problem over the phone.

3. If the problem requires service, the technician will issue a Returned Material Authorization

(RMA) number, which is required for service. If you require packaging, the technician can

arrange to send you proper packaging. Securely pack the UPS to avoid damage during shipping.

Do not use Styrofoam beads for packaging. Any damages (direct, indirect, special, incidental or

consequential) to the UPS incurred during shipment to Tripp Lite or an authorized Tripp Lite

service center is not covered under warranty. UPS Systems shipped to Tripp Lite or an authorized

Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on the

outside of the package. If the UPS System is within the 2-year warranty period, enclose a copy of

the sales receipt. Return the UPS for service using an insured carrier to the address supplied by the

Tripp Lite service technician.

WARRANTY REGISTRATION

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.

You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product! *

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

All manuals and user guides at all-guides.com

continued

USB Port

RS-232 Port

approximate battery charge level available to support equipment. During a prolonged

brownout or blackout, the alarm will sound continuously (and the "BATTERY CAPACITY"

Meter will show one 20% capacity segment shaded) to indicate the batteries are nearly out

of power; save files and shut down equipment immediately.

3f) "FAULT" Icon: This icon will illuminate and an alarm will sound after a self-test to

indicate the outlets are overloaded. To clear the overload, unplug some equipment from the

outlets and run the self-test repeatedly until the icon is no longer illuminated and the alarm

is no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately following a self-

test may cause the UPS to shut down and cease supplying output power in the event of

a blackout or brownout.

Tel/DSL/Network Jacks

in line from the coaxial wall jack. The UPS system must be plugged into a 3-wire grounded AC

outlet for coaxial line surge protection to work. Make sure cables connected to satellite dishes,

antennas, etc. are also grounded.

Power Sensitivity Dial: This dial is normally set fully counterclockwise, which enables the

UPS to protect against waveform distortions in its AC input. When such distortion occurs, the

UPS will normally switch to providing PWM sinewave power from its battery reserves for as

long as the distortion is present. In some areas with poor utility power or where the input power

comes from a backup generator, frequent brownouts and/or chronic waveform distortion could

cause the UPS to switch to battery too often, draining its battery reserves. Experimenting with

different settings for this dial may reduce how often your UPS switches to battery due to

waveform distortion or brownouts. As the dial is turned clockwise, the UPS becomes more

tolerant of variations in its input power's AC waveform. NOTE: The further the dial is adjusted

clockwise, the greater the degree of waveform distortion the UPS will allow to pass to

connected equipment. When experimenting with different settings for this dial, operate

connected equipment in a safe test mode so that the effect on the equipment of any waveform

distortions in the UPS's output can be evaluated without disrupting critical operations. The

experiment should last long enough to assure that all expected line conditions are encountered.

Battery Replacement: Under normal conditions, the original battery in the UPS will last

several years. Battery replacement should be performed only by qualified service personnel.

During

battery

replacement,

"Battery Warnings" in the Safety section. Tripp Lite offers a complete line of replacement batteries

at www.tripplite.com/support/battery/index.cfm.

FCC Part 68 Notice (United States Only)

If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible, they

will notify you in advance. If advance notice isn't practical, you will be notified as soon as possible. You will be advised of your right to file a complaint

with the FCC. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper operation

of your equipment. If it does, you will be given advance notice to give you an opportunity to maintain uninterrupted service. If you experience trouble with

this equipment's Modem/Fax Protection, please call Tripp Lite Technical Support at (773) 869-1234 for repair/warranty information. The telephone

company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure the equipment is not

malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax Protection. This equipment may not be used on coin service

provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or corporation

commission for information.)

FCC Radio/TV Interference Notice (U.S. only)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference using one or

more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the receiver; connect

the equipment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an experienced radio/television

technician for help. The user must use shielded cables and connectors with this product. Any changes or modifications to this product not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC

rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation.

Equipment Attachment Limitations (models with the Industry Canada label in Canada only)

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets the telecommunications network

protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements Document(s). The

Department does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection. The customer should be aware that the compliance with the above

conditions might not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this

equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe

system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make

connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

: DC Voltage

Coaxial Protection Jacks

Power Sensitivity Dial

qualified

service

personnel

Regulatory Compliance Identification Numbers