Blaupunkt Frankfurt RCM 82 Instrucciones De Montaje página 2

Notes on Safety
Instructions for installation and connection
Disconnect the minus pole of the battery during installation and connection.
When drilling holes, be sure not to damage any vehicle parts (battery,
cable, fuse box, etc.).
The positive cable must have a cross-section of at least 1 mm. The unit
is protected by a quick-acting fuse of 7,5 A.
The side panel of the car radio heats up considerably during
operation.
Attention: Thus pay attention that the cables are not in contact with
the housing.
Note:
By means of the support included in delivery you can mount the set in cars
with a DIN car radio cutout of 182 x 53 mm, an installation depth of 165
mm and an instrument panel thickness around the fixing clips of 1 - 20
mm, see fig. 1.
For cars with other cutout dimensions Blaupunkt delivers car-specific
installation kits for common car types for 50/52 mm sets. Use enclosed
distance plates only for installation kits of 52 mm sets.
Please check the dimensions and, if necessary, use a car-specific
installation kit, e. g. VW Golf II / Jetta II/: 7 608 3824 73.
When using installation sets for units of 52 mm, four distance plates,
order number 8 601 055 056 must be used, fig. 1a.
Preparation of car radio installation
Install the car radio into the DIN cutout provided in your car's dashboard
ex factory.
Prepare the car radio DIN cutout (unlock shelf or dummy cover) or cut out
the car radio compartment to 182 x 53 mm.
Grasp behind the car radio cutout and check how many of the fixing strips
of the car radio support may be bent.
Note:
Try to bend as many fixing strips as possible.
Insert the support into the cutout and bend the appropriate fixing strips
with a screwdriver, see fig. 1, 2.
Connection
Connection overview .................................................................... fig. 4
Notes on connection ..................................................................... fig. 5
Connection of equalizer and amplifier .......................................... fig. 6
Connection CD player .............................................................. fig. 7, 8
Loudspeaker connection:
4 speakers 4 x 20 W / 4 Ω ............................................................ fig. 9
2 speakers 2 x 25 W / 4 Ω .......................................................... fig. 10
2 speakers 2 x 25 W / 4 Ω with amplifier ..................................... fig. 11
Important note!
If these notes are disregarded, there is danger of destroying the
final stages.
Do not connect speaker outputs to ground!
Connection with multiple plug installed ex factory
In vehicles equipped with a system plug, the latter can be connected
together with plus, minus and loudspeaker line to the car-specific Quick-
Fit of the car radio, see fig. 12.
Connecton with vehicle specific QuickFit
For Audi, BMW, Opel, VW and Nissan vehicles a car specific QuickFit
(connecting box) is required. For 4-channel and preamp operation: Audi/
VW: 7 607 853 090, BMW: 7 607 739 090, Opel: 7 607 677 090, Nissan:
7 607 736 090.
For 2-channel and preamp operation: Audi/VW: 7 607 867 090
GB
Change connecting box
1. Loosen the screw and unlock the top and bottom support springs by
lifting them with a sharp object or a solid knife blade, see fig. 15.
2. Pull out the connecting box, see fig. 16.
3. For two channel operation, position the connecting box with the sides
in the correct position and parallel to the cabinet, and push it in
carefully, see fig. 17.
4. Tighten the screw and clip in the top and the bottom support screw.
5. Replace the fuse of the connecting box.
Connection with QuickOut installed ex factory
If a car is fitted with QuickOut ex factory (at present Opel), the QuickOut
ex factory has to be removed.
Ground cable
Do not connect the ground cable to the negative pole of the battery.
Route the ground cable to a suitable ground point (car body screw, car
body metal sheet) and shorten it accordingly.
Remove the insulation from the ground cable and attach the forked cable
lug (if necessary, solder it).
Scratch off the paint from the contact area of the ground point and
lubricate it with graphite grease (important for good ground contact).
Screw on the ground cable.
Positive cable (ACC +12 V) (ignition)
Connect the positive cable together with distributor to pin 30 (constant
power) or pin 15 (positive line connected via ignition) of the fuse holder
behind the fuse.
Permanent plus connection (Battery +12 V)
Connect the permanent plus terminal together with the cable and cable
clamp to a fuse-protected positive line (e.g. clock, warning flasher).
Control cable (Power Antenna +)
When connecting a fully automatic motor antenna, use the cable clamp
to fasten the control cable of the motor antenna to the control cable.
Lighting connection (Illumination)
Lighting connection for vehicles with adjustable dashboard lighting (plus-
controlled).
Telephone mute (Low)
If you have connected a car telephone, your car radio will be mutet during
telephone calls.
Telephone mute is not possible if a CD player is installed in your car.
Car radio installation
Insert the car radio from the front into the support and push in until the
stop springs on the sides engage right and left (distinct click to be heard).
Removal of the car radio
Insert the brackets right and left into the provided trimplate holes and
push in until you hear a distinct click (lateral springs are unlocked).
Using both brackets (see fig. 5), pull the unit out.
Note
Locked brackets can only be removed after taking out the unit.
QuickOut
Use the car-radio-specific QuickOut support.
Notes de sécurité
Instructions de montage et de branchement
Pendant le montage et le branchement des appareils, il convient de
déconnecter le pôle négatif de la battérie.
+12V
per. +12V
+12V
F