Before Starting - IKRA GBS 8050 LI Instrucciones De Uso

GB | Operating Instruction
• When working with the shears, always take a
stabile standing position, particularly when you
are using steps or a ladder.
• Do not use shears with a damaged or excessively
worn-out cutting part
• Ensure that all protective devices and handles
are installed on the machine. Never try to put an
incomplete machine in operation.
• Always use the protective part designed for the
blade when transporting and storing the shears.
• Before starting the work, make yourself familiar
with the surroundings and possible dangers
which you may not hear because of the noise.
• Only use the spare sparts and accessories
recommended by the manufacturer.

Before starting

Charging the battery
Safety Instructions:
The tool is delivered with the lithium-ion battery charged.
However, we recommend recharging the battery before
the tool is operated for the first time.
- Use the included charging unit for charging the battery
only. It is specially designed to match the tool's battery.
- Never use other charging unit. This will result in fire
and/or explosion hazard!
- Always keep the charging unit clear of rain or moisture.
Hazard of electric shock! - Never charge the battery
in the open without protection, always choose a dry,
protected place.
- Never try to charge third-party batteries with this
charging unit. This will result in fire and/or explosion
hazard!
- Check the housing, plug and cable for damage before
each use of the charging unit. Do not use the unit if
you detect damage.
- Do not open the charging unit by force. In case of a
defect, the charging unit must be replaced.
- The charging unit heats up during the charging
process. Do not place the unit on a flammable surface
or operate it in a flammable environment. Fire hazard!
- Never open the battery cells. Hazard of short circuits!
- In case of damage to the battery, hazardous vapours or
fluids may escape. In case of incidental contact flush
with water and seek medical advice immediately. The
fluid may have irritating or caustic effects on the skin.
- Protect the battery from heat, intense insolation and
fire. Explosion hazard!
Charging process:
To charge the battery connect the charging unit to an
electrical socket. Then connect the plug of the charging
cable to the charging socket of the grass and shrub
shears or trimmer (fig. 2)
The start of the charging process is indicated by the red
control light ("X", Fig. 2) at the end of the handle. If the
3
battery is completely empty the charging time is about
6 hours. After the battery has been fully charged, the
electronic control automatically switches off the charging
process. The red control light then changes its colour to
green indicating the end of the charging process. It is not
required to monitor the charging time.
The charging unit and the handle of the tool heat up
during the charging process. This is nothing unusual.
Pull the plug of the charging unit if it is not in use.
The tool must never be switched on during the charging
process!
Recharge the battery every time you realise a
considerable decrease of the tool's cutting performance.
The battery additionally features an electronic total
discharge protection that protects the battery from
damage. This feature switches the battery off if the
discharging threshold is reached. Do not switch the tool
on afterwards and make sure to recharge the battery
first.
Switching the tool on/off
Slide the switch-on lock A (fig. 5) forward and push
switch B. After the tool has been switched on, you do not
have to hold the switch-on lock A any longer.
To switch off just let go of the switch B.
Attention! The blades will coast for a certain
time after switch-off!
Refitting the tool / Changing the shear systems
Put the included blade guard into the blade(s) and use
protective gloves to protect yourself from injury.
Push both lateral push buttons concurrently and remove
the shearing blades (Fig. 5).
Remove any dirt from the gear area (if necessary).
Please slightly grease the drive area using commerci-
al universal grease as described in the Maintenance
section before putting the replacement shears in place
(Fig. 7).
Lead the cutting blades with the rear holding toe into
the housing of the grass shears as shown in fig. 6 and
lock the click system in place by strongly pushing on the
blade base plate.
The position of the eccentric drive does not have to be
considered when changing the blades. When the device
is switched on, the gear eccentric unit automatically
engages into the appropriate relief in the shearing blade.
The device is now ready for operation.
Hints for your work with the tool
The shrub trimmer cuts ornamental shrubs and light
undergrowth or bushes. The device is also well-suited for
ornamental cuts as, for example, for the care of graves.