Petzl METEOR III + A71 Manual Del Usuario página 3

(EN) ENGLISH
Field of application
- Helmet for climbing, mountaineering and other vertical sports.
- Helmet for cycling, roller skating and skateboarding. CE certification only.
- Helmet for canoeing, kayaking and whitewater sports. CE certification only.
This helmet is not designed for use in class 5 or 6 whitewater, as defined by the
International Canoe-Kayak Federation.
In whitewater, this helmet is designed to help protect against bumps, scrapes and
bruises.
Do not use this helmet in activities for which it is not designed.
Wearing a helmet can significantly reduce the risks associated with these activities,
but cannot entirely eliminate them. In a major impact, the helmet deforms to
absorb the maximum amount of energy possible, sometimes to the point of
destroying the helmet.
WARNING
Activities involving the use of this equipment are inherently dangerous.
You are responsible for your own actions and decisions.
Before using this equipment, you must:
- Read and understand all instructions for use.
- Get specific training in its proper use.
- Become acquainted with its capabilities and limitations.
- Understand and accept the risks involved.
Failure to heed any of these warnings may result in severe injury or death.
Responsibility
WARNING, specific training in the activities defined in the field of application is
essential before use.
This product must only be used by competent and responsible persons, or those
placed under the direct and visual control of a competent and responsible person.
Gaining an adequate apprenticeship in appropriate techniques and methods of
protection is your own responsibility.
You personally assume all risks and responsibilities for all damage, injury or death
which may occur during or following incorrect use of our products in any manner
whatsoever. If you are not able, or not in a position to assume this responsibility or
to take this risk, do not use this equipment.
Nomenclature of parts
(1) Shell, (2) Headband, (3) Headband adjustment clips, (4) Chin strap adjustment
(front-back), (5) Chin strap buckle and adjuster, (6) Inserts for face shield
mounting, (7) Headlamp clips, (8) I.D. zone, (9) Headband attachment inserts.
Principal materials: shell made of expanded polystyrene and polycarbonate, straps
made of polyester.
Inspection, points to verify
Before each use, verify that there are no cracks or deformities on the inside or
outside of the shell and the internal liner, check that the straps, stitching, and the
headband attachment system are undamaged, and that the headband adjustment
system and chinstrap buckle are working properly.
WARNING, a major impact to the helmet can significantly reduce its protective
properties without leaving visible signs of damage. Retire your helmet after a major
impact.
Consult the details of the inspection procedure to be carried out for each item of
PPE on the Web at www.petzl.com/ppe
Contact PETZL if there is any doubt about the condition of this product.
How to put on and adjust the helmet
Diagram 1. Headband
- Put the helmet on your head, pinch the two headband adjustment clips (3) and
adjust the headband for a comfortable fit.
You can adjust the positioning of the headband on the nape of the neck by sliding it
up or down on the webbing.
The helmet should fit snugly and not move about on the head. A poorly-adjusted
helmet will not provide effective protection.
Diagram 2. Chinstrap
- Position the adjusters (5) under the ears. To adjust the chinstrap backwards or
forwards, slide the webbing through the adjusters.
- Fasten the chinstrap using the buckle (5). Tighten the chinstrap to fit comfortably.
A correctly adjusted chinstrap reduces the risk of the helmet coming off
accidentally.
Functionality test
Your helmet must be correctly fastened and centered on the head. A well-adjusted
helmet (minimal movement front to back or side to side), provides better
protection. Make sure that it is correctly adjusted, that the webbing straps, the chin
strap and head band are properly tightened.
DO NOT USE THIS HELMET if you are unable to adjust it to fit properly. Replace it
with a helmet of a different size or model.
Precautions for use
- Warning, because of its design, this helmet is vulnerable to damage from
improper care. Do not sit on it, pack it too tightly, drop it, allow it to contact sharp
or pointed objects, etc.
Do not expose your helmet to high temperatures, for example by leaving it inside a
vehicle in direct sunlight.
- Paint and stickers may contain materials that, with time, can alter the physical
properties of the helmet. Before applying any of these products to the helmet,
verify their compatibility with polystyrene and polycarbonate.
- Certain chemical products, especially solvents, can damage your helmet. Protect
your helmet.
Petzl general information
Lifetime / When to retire your equipment
For Petzl's plastic and textile products, the maximum lifetime is 10 years from the
date of manufacture. It is indefinite for metallic products.
ATTENTION: an exceptional event can lead you to retire a product after only one
use, depending on the type and intensity of usage and the environment of usage
(harsh environments, marine environment, sharp edges, extreme temperatures,
chemical products, etc.).
A product must be retired when:
- It is over 10 years old and made of plastic or textiles.
- It has been subjected to a major fall (or load).
- It fails to pass inspection. You have any doubt as to its reliability.
- You do not know its full usage history.
- When it becomes obsolete due to changes in legislation, standards, technique or
incompatibility with other equipment, etc.
Destroy retired equipment to prevent further use.
Product inspection
In addition to the inspection before each use, an in-depth inspection must be
carried out by a competent inspector. The frequency of the in-depth inspection
must be governed by applicable legislation, and the type and the intensity of use.
Petzl recommends an inspection at least once every 12 months.
To help maintain product traceability, do not remove any markings or labels.
Inspection results should be recorded on a form with the following details: type of
equipment, model, manufacturer contact information, serial number or individual
number, date of manufacture, date of purchase, date of first use, date of next
3
A71_METEORIII_A715000D (290110)
periodic inspection, problems, comments, the name and signature of the inspector.
See an example at www.petzl.com/ppe
Storage, transport
Store the product in a dry place away from exposure to UV, chemicals, extreme
temperatures, etc. Clean and dry the product if necessary.
Modifications, repairs
Modifications and repairs outside of Petzl facilities are prohibited (except
replacement parts).
3-year guarantee
Against all material or manufacturing defect. Exclusions: normal wear and tear,
oxidation, modifications or alterations, incorrect storage, poor maintenance,
negligence, uses for which this product is not designed.
Responsibility
PETZL is not responsible for the consequences, direct, indirect or accidental, or
any other type of damage befalling or resulting from the use of its products.