Technical Data; Filling The Magazine; Noise/Vibration Information - KMR 3483 Manual Del Usuario

4 I English
1

TECHNICAL DATA

Type Type
Type Type
Dimensions mm
Weight kg (without fasteners)
Single sequential or contact actuation
Recommended operating pressure
range
Maximun permissible operating
pressure
Air consumption per driving
operation
Magazine capacity.
(No. of fasteners)
Penetration depth setting
Lighting
Fasteners: Brad Fasteners: Brad nails nails
Fasteners: Fasteners: Brad Brad nails nails
Brad length mm
Wire thickness mm
Recomme Recomme Recommended Recomme nded nded lubricant nded lubricant lubricant lubricant
1 litre special oil. Code No.
250 cm3 grasa especial. Code No.
2

NOISE/VIBRATION INFORMATION

Noise characteristic Noise characteristic values
Noise Noise characteristic characteristic
A-weighted single-event emission
sound pressure level at work
station L pA, 1s
A-weighted sound power level
L WA, 1s, d
Vibration characteristic Vibration characteristic values
Vibration Vibration characteristic characteristic
Weighted r.m.s.-acceleration (a)
The noise level when working can exceed 85
dB (A). Wear Wear ear ear protection!
Wear Wear ear ear
* Measured values determined according to
EN 12549:1999.
** Measured values determined according to
ISO 8662-11:1999.
3 SUPPLIED WITH
1 Mini brad nailer
1 Tool use and safety instructions
1 Technical data sheet
1 Transport case
KMR
3483 3483
3483 3483
255/244
1.2 kg
5 - 8.4 bar/
0.5 - 0.84 MPa
8.4 bar/
0.84 MPa
0.85 l at 7
bar / 0.7 MPa
105
yes
yes
15 - 55
1.0 x 1.25
9 4420
68 3868
values * * * * 3483 3483
values values 3483 3483
80.7 dB(A) 80.7 80.7 80.7 dB(A) dB(A) dB(A)
93.7 93.7 dB(A) 93.7 93.7 dB(A) dB(A) dB(A)
values ** **
values values ** **
< < < < 2.5 2.5 m/s2 m/s2
2.5 2.5 m/s2 m/s2
protection!
protection! protection!
4

FILLING THE MAGAZINE

Only those fasteners specified under technical data
(see 1) may be used.
When filling the magazine, hold the tool so that the
muzzle is not pointing towards own body or towards
any other person.
Do not load the tool with fasteners with the safety
yoke or trigger depressed.
Place the tool on its side. Press the locking lever (l) and
pull the magazine rail (m) back. Introduce the nails tip
downwards and push the magazine rail forward until
it locks into place.
5 FIL PENETRATION DEPTH SETTING
The penetration depth of the nail head is adjusted
using air pressure. Should this not suffice, a more
exact setting of the penetration depth can be achieved
by turning the setting nut (p).
Right-hand turn (U) = less penetration depth.
Left-hand turn (D) = more penetration depth.
6 SWITCHABLE ACTUATION
-SINGLE TRIGGER RELEASE/RELEASE ON CONTACT-
A setting wheel on the trigger (s) can be turned to set
the type of actuation either to single trigger release
or release on contact (see symbol).
7 ACCESSORIES
Balancer for 10 - 20 n (1.0 - 2.0 kp),
cable travel 1.6 m (5.2 ft).
3483
Code No. Code Code Code No. No. No.
40 3393