Tabla de contenido
4.8 MOUNTING THE GRASS
CATCHER BAG
• For TC model
1. First assemble the frame, uniting the
upper part (fig. 9.A) with the lower
part (fig. 9.B), using the nuts and bolts
supplied (fig. 9.C) as indicated.
Position the angular plates (fig. 9.D)
e (fig. 9.E), respecting the right (R⇑)
left (L⇑) alignment, and securing
them to the frame using four self-
tapping screws (fig. 9.F).
2. Models with electrical tipping
function only: Mount the two rollers
(fig. 9.G) on the support pins(fig. 9.H),
making sure that the collect is facing
the support, and secure it using
elastic rings (fig. 9.I). Next, secure the
supports to the front frame (fig. 9.B)
using the nuts and bolts (fig. 9.J).
3. Insert the frame into the canvas cover
(fig. 9.K), making sure that it is positioned
correctly around the base. Attach the
various plastic profiles to the frame
tubes using a screwdriver (fig. 9.L).
4. Insert the handle (fig. 9.M) via the holes
on the cover (fig. 9.N), and secure the
resulting sub-assembly to the frame
using the screws (fig. 9.O) as indicated,
and the rear self-tapping screws (fig. 9.P).
5. Mount the strengthening cross bar
(fig. 9.Q) under the frame using the
nuts and bolts (fig. 9.R), so that the
flat part is facing the canvas. Insert
the emptying lever (fig. 9.S) into its
housing and fit the retaining screw
(fig. 9.T) and associated nut (fig. 9.U).
• TS-TX-TH models
Complete the grass catcher mounting
sequence as described in the instruction
sheets supplied with the components.
4.9 MOUNTING THE GRASS
CATCHER TIPPING LEVERS
Position the levers shaft (fig. 10.A) so
that it lies in the groove in the two plates
(fig. 10.B) and secure it to the inner
part of the grass catcher bag supports
(fig. 10.C), using the nuts and bolts (fig.
10.D) supplied in accordance with the
sequence indicated in the figure.
Connect the end of the lifting piston
shaft (fig. 10.E) to the lever (fig. 10.F) by
means of the pin (fig. 10.G) and mount
the two elastic rings (fig. 10.H).
Before mounting the grass catcher
bag on its support, make sure that
tipping levers move correctly.
4.10 MOUNTINGTHECUTTING-
MEANS ASSEMBLY LATERAL
SAFETYPANELS(IFFITTED)
Mount the safety panels (fig. 11.A) using
the screws (fig. 11.B) and nuts (fig. 11.C)
supplied, in accordance with the instructions
provided for each machine type.
4.11 SIDE DUMPING CHUTE
ASSEMBLY(FORMODELS
WITHSIDEDUMPINGONLY)
1. From the inside of the side dumping chute
(fig. 12.A), fit the spring (fig. 12.B) by
inserting the terminal (fig. 12.B.1) into the
hole and turning it so that both the spring
(fig. 12.B) and the terminal (fig. 12.B.2)
are securely positioned in their housings.
2. Position the side dumping
chute (fig. 12.A) in line with the
cutting-means assembly brackets
(fig. 12.C). Using a screwdriver, turn
the second terminal (fig. 12.B.2)
of the spring (fig. 12.B) to bring it
outside the side dumping chute.
3. Fit the pin (fig. 12.D) in the holes on
the brackets (fig. 12.C) and on the
side dumping chute, so that it passes
through the coils of the spring (fig.
12.B) and the drilled end comes
out of the inner most bracket.
EN - 9
Tabla de contenido
