Protecting The Environment - Stanley FATMAX SFMCMW2653 Traducido De Las Instrucciones Originales

página de 156

/ 156
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

5. Install the plastic blade insulator

the raised lips on one side engage the edges of the blade.

6. Install the blade spacer

lips on the other side of the blade insulator. Be sure to align

the flats in the hole of the blade spacer with the flats of

the shaft, rotating the blade and blade insulator together

as necessary.

7. Position piece of wood to keep blade from turning as shown

in Fig. L. Install flange nut

blade spacer

and securely tighten the blade

wrench

Blade Sharpening

KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL

BLADE DOES NOT CUT GRASS CLEANLY.

WARNING: Use gloves and proper eye protection while

removing, sharpening, and installing blade. Ensure that

safety key and battery pack are removed.

Sharpening the blade twice during a mowing season is usually

sufficient under normal circumstances. Sand causes the blade

to dull quickly. If your lawn has sandy soil, more frequent

sharpening may be required. REPlACE BEnT OR DAMAgED

BlADE iMMEDiATElY.

When Sharpening the Blade

•

Make sure blade remains balanced.

•

Sharpen blade at the original cutting angle.

•

Sharpen cutting edges on both ends of blade, removing

equal amounts of material from both ends.

To Sharpen Blade in a Vise (Fig. M)

1. Be sure the bail handle is released, the blade has stopped

and safety key and battery pack are removed before

removing the blade.

2. Remove blade from mower. See instructions for Removing

and Installing Blade.

3. Secure blade

in a vise

4. Wear proper eye protection and gloves and be careful not

to cut yourself.

5. Carefully file the cutting edges of the blade with a fine tooth

file

or sharpening stone, maintaining the angle of the

original cutting edge.

6. Check balance of blade. See instructions for

Blade Balancing.

7. Replace blade on mower and tighten securely.

Blade Balancing (Fig. N)

Check balance of the blade

blade over a nail or round screwdriver

in a vise

. If either end of the blade rotates downward, file

along the sharp edge of that dropping end. Blade is properly

balanced when neither end drops.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require no lubrication.

on the blade such that

so that it sits inside the raised

with the flange against the

by placing center hole in the

, clamped horizontally

Cleaning

Release bail handle

stop and then remove safety key. Clean out any clippings which

may have accumulated on the underside of the deck. After

several uses, check all exposed fasteners for tightness.

WARNING: Blow dirt and dust out of the main housing

with a

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into a liquid.

Release bail handle

to a stop and then remove battery and safety key. Clean out

any clippings which may have accumulated on the underside

of the deck. After several uses, check all exposed fasteners

for tightness.

Corrosion

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows:

Release bail handle

and safety key. Wipe all exposed parts with a damp cloth.

CAUTION: Do not pour or spray water on the mower

in an attempt to clean IT. Do not store the tool on or

adjacent to fertilizers or chemicals. Such storage can cause

rapid corrosion.

Optional Accessories

WARNING: Since accessories, other than those offered by

STANLEY FATMAX, have not been tested with this product,

use of such accessories with this tool could be hazardous.

To reduce the risk of injury, only STANLEY FATMAX

recommended accessories should be used with

this product.

Consult your dealer for further information on the

appropriate accessories.