READ ThE fOLLOWING INSTRUCTIONS ThROUGhOUT
BEfORE STARTING ThE INSTALLATION
Important
Check the tub upon reception throughout (specifically, check for
visible damage to the exterior packaging). Notify the carrier if
damage is found, in accordance with the laws in force.
ChECK ThAT ThE ARRANGEMENTS ARE SUITED TO ThE
INDICATIONS ShOWN ON ThE PRE-INSTALLATION CARD.
m (IEC 60335-1/A2:2006) The pressure in the plumbing
system feeding the device must not exceed 600 kPa (6 bars).
Preliminary operations
two people are required to install the infinito® tub on an
appropriately levelled surface.
the tub may be installed on a finished floor or raised platform.
remember that the weight of the tub full of water on the floor is
considerable (see preliminary installation instruction card).
0
n (
1 part 1) arrange the tub in the installation position
holding it raised from the ground with wooden blocks.
(part 2) assemble the siphon drainage column and tighten the
ring nut well.
(part 3) connect the siphon to the drain pipe prepared for this
purpose and carefully apply silicone to the joints.
(part 4) for perfect sealing, apply silicone or equivalent sealant to
the drainage column seal.
(part 5) using an allen wrench, tighten the ring nut on the
drainage column to tighten it well.
(part 6) run water into the tub (with the drain plug open) for
a few minutes and check that all connections are sealed. check
that there are no leaks.
(part 7) screw the "click-clack" plug onto the drainage column.
0
n (
2 part 1) remove the wooden blocks and rest the tub on
the floor.
(part 2) level the tub and check that the tub drains smoothly
and completely.
(part 3) if necessary, install wedges on the resting surface for
extra thickness.
(part 4-5) if the tub is fixed to the floor, it is advisable to raise
it slightly and apply a non-acetic silicone bead (approximately 1
cm) around the entire perimeter of the tub.
at the end of the operation, reposition the tub on the floor and
check that it is levelled perfectly.
Maitenance
Daily maintenance
soap and water or common detergent is recommended for
cleaning the techstone® tub.
gel detergents, abrasive detergents and scouring pads of the
"scotch brite®" type may be safely used on techstone®. rinse all
surfaces carefully after cleaning.
how to remove stubborn stains, scratches and burns
use of a "scotch brite®" type scouring pad and an abrasive
cleaning product is recommended for removing stubborn stains,
scratches, cigarette burns and small scuffs.
rub the surface of the concerned part. if this is not enough,
rub the area with very fine sandpaper and cream or powder
detergent containing micro granules to delicately scrape the
surface. methylated spirit may be used. rinse the treated surface
carefully afterwards.
Cautions
n The device must not be used by motor, sensory or
cognitively impaired individuals, children or anyone who
has not been sufficiently instructed on their own. Children
must be supervised by a person responsible for their safety.
n Jacuzzi® tubs are designed for home use or the like and
must be installed and used only indoors.
n It is dangerous to use or access electric devices from inside
the tub (radio, hairdryer, etc.).
n Be careful if you want to use the tub on your own: soaking
in hot water for a long time can cause nausea, dizziness and
fainting.
n It is not recommended to use the tub taking drugs or
medicines which can induce sleepiness or raise/lower your
blood pressure.
n Never use water hotter than 40 °C.
n Use of aggressive chemical products, such as nail polish
remover, trichloroethylene, strong acids (hydrochloric
acid, etc.) and strong bases (caustic soda, etc.), industrial
detergents, paint solvents is NOT RECOMMENDED for
cleaning.
DO NOT use metallic scrapers, iron brushes or other metallic
tools for removing stains, paint, plaster or the like.
Some substances, such as ink, cosmetics and colourings,
may stain the surface of the tub in depth and beyond repair
in case of prolonged contact. Cigarettes may cause similar
damage.
4