Terex Genie Z-45/25 Manual Del Operario página 8

Manual del operario
Seguridad general
Señales de
seguridad y
ubicaciones
31060
114397
DANGER
6
114389
DANGER
Improper Use Hazard
The operator is responsible for safe machine
operation. This includes:
1 Avoid hazardous situations.
2 Always perform a pre-operation inspection.
3 Always perform function tests prior to use.
4 Inspect work place.
5 Only use the machine as it was intended.
Do not operate unless:
You read, understand and obey:
- manufacturer's instructions and safety rules —
safety and operator's manuals and decals
- employer's safety rules
- applicable governmental regulations
You are properly trained to safely operate this machine.
Electrocution Hazards
This machine is not electrically
insulated and will not provide
protection from contact with or
proximity to electrical current.
Maintain Required Clearance
Line Voltage Required Clearance
0 to 50KV 10 ft 3.0 m
50 to 200KV 15 ft 4.6 m
200 to 350KV 20 ft 6.1 m
350 to 500KV 25 ft 7.6 m
500 to 750KV 35 ft 10.6 m
750 to 1000KV 45 ft 13.7 m
Tip-over Hazards
Do not raise or extend boom
unless machine is on firm, level
ground.
Do not depend on tilt alarm as a
level indicator. Tilt alarm sounds in
platform only when machine is on a
severe slope.
Do not raise boom when wind speeds may exceed 28
mph / 12.5 m/s.
Do not operate machine in strong or gusty winds. Do not
increase surface area of platform or load. Increasing
area exposed to wind will decrease machine stability.
Do not drive machine on or near
uneven terrain, unstable surfaces or
other hazardous conditions with
boom raised or extended.
Do not drive machine on a slope
that exceeds the maximum slope or
side slope rating for the machine.
Use extreme care and slow speeds while driving the
machine in stowed position across uneven terrain,
debris, unstable or slippery surfaces and near holes
and drop-offs.
Do not attempt to free a caught or snagged platform
using platform controls. All personnel must be removed
from platform before attempting to free platform using
ground controls.
31060
DANGER
Tip-over Hazard
Altering or disabling limit switches
can result in machine tip-over.
Machine tip-over will result in
death or serious injury.
Do not alter or disable limit switch(s).
Z-45/25 • Z-45/25J
Cuarta edición • Primera impresión
Do not alter or disable machine components that in any
way affect safety and stability.
Do not push off or pull toward any
object outside of the platform.
Do not place or attach overhanging
loads to any part of this machine.
Do not place ladders or scaffolds in
platform or against any part of this
machine.
Do not use machine on a moving or mobile surface or
vehicle.
Be sure all tires are in good condition, air-filled tires are
properly inflated and lug nuts are properly tightened.
Fall Hazards
Occupants must wear a safety
belt or harness in accordance
with governmental regulations.
Attach lanyard to anchor
provided in platform.
Do not sit, stand or climb on
the platform guard rails.
Maintain a firm footing on the
platform floor at all times.
Do not climb down from the
platform when raised.
Lower the platform entry mid-
rail or close the entry gate
before operating.
Collision Hazards
Be aware of limited sight distance and blind spots when
driving or operating.
Check work area for overhead
obstructions or other possible
hazards.
Be aware of crushing hazard
when grasping the platform
guard rail.
Observe and use color-coded
direction arrows on the platform
controls and drive chassis for
drive and steer functions.
Do not lower the boom unless the area below is clear of
personnel and obstructions.
Explosion Hazard
Do not start engine if you smell or detect liquid
petroleum gas (LPG), gasoline, diesel fuel or other
explosive substances.
Do not refuel the machine with the engine running.
Damaged Machine Hazards
Do not use a damaged or malfunctioning machine.
Be sure all maintenance has been performed as
specified in the appropriate operator's and service
manuals
Be sure all decals are in place and legible.
Be sure safety, operator's and responsibilities manuals
are complete, legible and in the storage container
located on the platform.
114389 A
28236
WARNING
Read and understand Operator's
Manual, Responsibilities Manual and
Safety Manual and all safety signs
before using or maintaining machine.
If you do not understand the
Improper operation or
information in the manuals, consult
maintenance can result in
your supervisor, the owner or the
serious injury or death.
manufacturer.
31060 B
N° de pieza 114339SP
114397
114389
28236
28236 D