Parts List - Silverline 802092 Manual Del Usuario

GB
g) ALWAYS support large workpieces on the in-feed and out-feed sides of the router table,
and where necessary, also to the sides. Use an additional stand wherever possible.
h) ALWAYS use guards, fences, horizontal and vertical featherboards etc., to guide the
workpiece, counteract and avoid kickback, especially when routing small or narrow
workpieces. Vertical featherboards attached to the fence also help prevent uncontrolled lift-up of
the workpiece.
i) ALWAYS remove ALL loose objects from the table before operating. Vibrations may cause
loose objects to move and come into contact with the cutter.
j) NEVER attempt to remove wood fragments or dust from the cutter with your hands, whilst
the router bit is spinning. ALWAYS switch the router off, disconnect the machine from the
power supply, and wait until the cutter has come to a standstill. ALWAYS use cut-proof gloves
when touching the cutter, to avoid injury.
k) ALWAYS inspect the workpiece for nails, staples and other metal objects and foreign
bodies. If the router cutter hits a concealed nail, the bit may be destroyed, high-velocity
projectiles may be produced, kickback can occur, all of which can lead to serious injury.
l) WHEREVER possible, use blind cutting techniques, where the router bit does not protrude
from underneath the workpiece. Keeping the cutter on the underside of the workpiece
provides additional operator protection .
m) ONLY expose the smallest possible part of the cutter above the table surface. Keep any
unused portion of the cutter below the table surface.
n) ALWAYS test any new setup by rotating the spindle by hand, with the machine
disconnected from the power supply. Ensure proper cutter clearance to the throat place, fence
and guard, before starting the machine .
o) ALWAYS use suitable throat plates, providing optimum clearance around the router bit .
p) ALWAYS use the router cutter guard, and adjust the guard to cover as much of the router bit as
possible, as close to the workpiece as possible. This not only protects the user from accessing the
revolving router cutter, it also provides effective dust extraction
q) LIMIT the depth of cut; NEVER remove too much material in one pass. Several passes with at
smaller cutting depth are safer, and produce a better surface finish.
r) ENSURE to adjust the router cutter speed, according to router cutter diameter and material
being cut. Use the speed selection dial on the plunge router .
s) ALWAYS feed AGAINST the rotation of the cutter. Both feed direction and rotation are
indicated by arrows on the router table surface.
t) ALWAYS use the fence if using a cutter without bearing or pilot. ALWAYS support the
workpiece firmly against the fence. NEVER remove the retractable guards on the fence. ALWAYS
use a cutter with bearing or pilot for freehand work.
Additional safety information
• ONLY use router cutters in perfect working condition compatible with the specification of the
router table and which are suitable for hand feeding operation (marked 'MAN' for manual
operation according to EN 847-1)
• The bit must not enter the workpiece in the same direction as the feed direction, which is likely
to cause the workpiece to climb (climb cutting) and may lead to loss of control during operation
with the workpiece pulled away from the operator in a hazardous way
• Do not attempt to re-sharpen router cutters unless you specifically follow the manufacturer's
instructions and have the equipment to do so. The majority of router cutters have blades that
cannot be re-sharpened and must be replaced immediately if dull
• Do not create fence traps caused by improper fence location. Fence traps happen when the fence
is positioned so far back that the front side of the workpiece would be behind the router cutter.
These are dangerous due to the risk of climb cutting and the difficulty of keeping the workpiece
against the fence
• Ensure the correct table insert (table ring) is fitted that is the correct size for the size of the router
cutter fitted
• Never use a router table until fully assembled and always re-check fasteners after re-assembly
after storage
• Make certain the router is not plugged into the power outlet when installing into the table or
when making adjustments or changing accessories
• DO NOT plug the router into a standard mains wall socket. It must be plugged into the router
table switch box so can be switched off in emergency situations
• The router table must be installed on a solid level surface and secured so the table will not
tip. Use of auxiliary in-feed and out-feed supports is necessary for long or wide workpieces.
Long workpieces without adequate support could cause the table to tip towards the operator
causing injury
• Routers create a lot of vibration and can work loose from their mountings. Check the mountings
frequently and re-tighten if necessary
• Never start the tool with the router cutter already engaged in the workpiece. This can lead to a
lack of control and possible injury
• The router table is designed to cut flat, straight and squared material only. Do not cut material
that is warped, uneven, weak or made from inconsistent material. If necessary make sure
material is correctly prepared before use . Incorrect material can lead to a lack of control and
possible injury
WARNING: Unmaintained tools can cause uncontrolled situations. ONLY use router cutters
that are correctly sharpened, maintained and adjusted in accordance with the manufacturer's
instructions .
Note: Seek professional training and assistance before attempting work that require procedures you
are not familiar with. STOP using the router table, if, at any point during operation, you encounter
difficulties or are uncertain how to proceed safely.
8

Parts List

1. Table (x 1)
2. Fence & Guard Assembly (x 1)
3. Table Extension (x 2)
4. Leg (x 4)
5. Switchbox (x 1)
6. Table Inserts (5 sizes)
7. Large Washer (x 3)
8. Small Washer (x 5)
9. Phillips Head Bolt (x 20)
10. Nut (x 24)
11. Featherboard Pad (x 2)
12. Knob (x 3)
13. Featherboard
Coach Bolt (x 4)
14. Fence Bolt (x 2)
15. Featherboard Wing Nut (x 4)
16. Large Washer (x 7)
17. Fence Knobs (x 2)
18. Router Securing Bar (x 4)
19. Bolt (x 2)
20. Router Securing Bolts (x 4)
21. Guard (x 1)
22. Guard Spring (x 1)
23. Guard Screw (x 1)
24. Adjustable Fence (x 1)
25. Protractor Guide Bar (x 1)
26. Protractor Body (x 1)
27. Protractor Knob (x 1)
28. Router Trigger Clamp (x 1)
29. Router Trigger Clamp Knob (x 1)
30. Featherboard (x 3)
31. Short Bolt (x 1